Yaskawa Sigma-5 User Manual: Design and Maintenance - Linear Motors - Manual (Page 100)

4 Operation
4.2.4 Electronic Gear
4-10
„ Feedback Resolutions of Linear Scale
Calculate the electronic gear ratio with the values in the following table.
Note: Pn282 is not valid when the linear scale is directly connected to the SERVOPACK and a serial converter unit is not
used. Check the linear scale pitch on the Un084 and Un085 monitors.
∗1. Models for serial converter units.
∗2. When using the encoder pulse output with these linear scales, the setting range of Pn281 is restricted. For details,
refer to 4.2.6 Setting Encoder Output Pulse.
∗3. Model for sensor head with interpolator.
∗4. Model for interpolator.
∗5. Model for interface unit by Heidenhain.
∗6. For details on this linear scale, contact Mitutoyo.
Refer to the manuals for the linear scale and the serial converter unit for details on the scale pitch and the num-
ber of divisions on the linear scale.
Type of
Linear Scale
Manufacturer Linear Scale Model
Linear
Scale Pitch
[ μm]
Model of Relay
Device between
SERVOPACK and
Linear Scale
Number
of
Divisions
Resolution
Incremental
Heidenhain
LIDA48 20
JZDP-D003-000-E *1 256 0.078 μm
JZDP-G003-000-E
*1 4096 0.0049 μm
LIDA18 40
JZDP-D003-000-E *1 256 0.156 μm
JZDP-G003-000-E *1 4096 0.0098 μm
LIF48 4
JZDP-D003-000-E *1 256 0.016 μm
JZDP-G003-000-E *1 4096 0.00098 μm
Renishaw plc RGH22B 20
JZDP-D005-000-E *1 256 0.078 μm
JZDP-G005-000-E
*1 4096 0.0049 μm
Magnescale Co., Ltd.
SR75- LF *2 80 – 8192 0.0098 μm
SR75- MF 80 – 1024 0.078 μm
SR85- LF
*2 80 – 8192 0.0098 μm
SR85- MF 80 – 1024 0.078 μm
SL700 *2 , SL710 *2 ,
SL720 *2 , SL730 *2
800
PL101-RY
*3
8192 0.0977 μm
MJ620-T13 *4
Absolute
Heidenhain LIC4100 20.48 EIB3391Y *5 4096 0.005 μm
Mitutoyo Corporation
ST781A/ST781AL 256 – 512 0.5 μm
ST782A/ST782AL 256 – 512 0.5 μm
ST783/ST783AL 51.2 – 512 0.1 μm
ST784/ST784AL 51.2 – 512 0.1 μm
ST788A/ST788AL 51.2 – 512 0.1 μm
ST789A/ST789AL *6 25.6 – 512 0.05 μm
Magnescale Co., Ltd.
SR77- LF *2 80 – 8192 0.0098 μm
SR77- MF 80 – 1024 0.078 μm
SR87- LF *2 80 – 8192 0.0098 μm
SR87- MF 80 – 1024 0.078 μm
Electronic gear ratio setting range: 0.001 ≤ Electronic gear ratio (B/A) ≤ 4000
If the electronic gear ratio is outside this range, a parameter setting error 1 (A.040) will
be output.