Yaskawa Sigma-5 User Manual: Design and Maintenance - Linear Motors - Manual (Page 230)

6.9 Gain Adjustment of Analog Monitor Output (Fn00D)
6-19
6
Utility Functions (Fn
)
(2) Operating Procedure
Follow the steps below to perform the gain adjustment of analog monitor output.
Step Display Example Keys Operation
1
Press the Key to view the main menu for the util-
ity function mode.
Use the
or Key to move through the list,
select Fn00D.
2
Press the Key. The display is switched to the
execution display of Fn00D.
Note:
If the display is not switched and “NO-OP” is dis-
played in the status display, the Write Prohibited Set-
ting (Fn010 = 0001) is set. Check the setting and
reset. (Refer to 6.12.)
3
Press the or Key to adjust the gain adjust-
ment width of CH1 (force reference monitor).
4
After the gain adjustment of CH1, press the Key.
The cursor moves to CH2 (motor speed monitor)
side.
5
Press the or Key to adjust the gain adjust-
ment width of CH2.
6
After having completed the adjustment both for CH1
and CH2, press the
Key.
The adjustment results are saved in the SERVO-
PACK. After the saving is completed, “DONE” is
displayed in the status display.
7
Press the Key to return to the Utility Function
Mode main menu.
㧮㧮ޓޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙
㧲㨚㧜㧜㧲㧦㧯㨡㨞㧹㨍㨚㨡㧭㨐㨖
㧲㨚㧜㧜㧱㧦㧯㨡㨞㧭㨡㨠㨛㧭㨐㨖
㧲㨚㧜㧜㧰㧦㧹㨛㨚㧳㨍㨕㨚ޓ㧭㨐㨖
㧲㨚㧜㧜㧯㧦㧹㨛㨚㨆㨑㨞㨛ޓ㧭㨐㨖
㧮㧮ޓޓޓޓޓ㧙㧳㨍㨕㨚ޓ㧭㧰㧶㧙
㧯㧴㧝㧩㧙㧜㧜㧜㧜㧝
㨁㨚㧜㧜㧞㧩ޓ㧜㧜㧜㧜㧜
㧯㧴㧞㧩㧙㧜㧜㧜㧜㧝
㨁㨚㧜㧜㧜㧩ޓ㧜㧜㧜㧜㧜
㧮㧮ޓޓޓޓޓ㧙㧳㨍㨕㨚ޓ㧭㧰㧶㧙
㧯㧴㧝㧩ޓ㧜㧜㧝㧞㧡
㨁㨚㧜㧜㧞㧩ޓ㧜㧜㧜㧜㧜
㧯㧴㧞㧩㧙㧜㧜㧜㧜㧝
㨁㨚㧜㧜㧜㧩ޓ㧜㧜㧜㧜㧜
㧮㧮ޓޓޓޓޓ㧙㧳㨍㨕㨚ޓ㧭㧰㧶㧙
㧯㧴㧝㧩ޓ㧜㧜㧝㧞㧡
㨁㨚㧜㧜㧞㧩ޓ㧜㧜㧜㧜㧜
㧯㧴㧞㧩㧙㧜㧜㧜㧜㧝
㨁㨚㧜㧜㧜㧩ޓ㧜㧜㧜㧜㧜
㧮㧮ޓޓޓޓޓ㧙㧳㨍㨕㨚ޓ㧭㧰㧶㧙
㧯㧴㧝㧩ޓ㧜㧜㧝㧞㧡
㨁㨚㧜㧜㧞㧩ޓ㧜㧜㧜㧜㧜
㧯㧴㧞㧩㧙㧜㧜㧝㧞㧡
㨁㨚㧜㧜㧜㧩ޓ㧜㧜㧜㧜㧜
㧰㧻㧺㧱ޓޓޓ㧙㧳㨍㨕㨚ޓ㧭㧰㧶㧙
㧯㧴㧝㧩ޓ㧜㧜㧝㧞㧡
㨁㨚㧜㧜㧞㧩ޓ㧜㧜㧜㧜㧜
㧯㧴㧞㧩㧙㧜㧜㧝㧞㧡
㨁㨚㧜㧜㧜㧩ޓ㧜㧜㧜㧜㧜
㧮㧮ޓޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙
㧲㨚㧜㧜㧲㧦㧯㨡㨞㧹㨍㨚㨡㧭㨐㨖
㧲㨚㧜㧜㧱㧦㧯㨡㨞㧭㨡㨠㨛㧭㨐㨖
㧲㨚㧜㧜㧰㧦㧹㨛㨚㧳㨍㨕㨚ޓ㧭㨐㨖
㧲㨚㧜㧜㧯㧦㧹㨛㨚㨆㨑㨞㨛ޓ㧭㨐㨖