Brocade Unified IP MIB Reference (Supporting FastIron Release 07.5.00) - Manual (Page 334)

306 Unified IP MIB Reference
53-1002549-02
VLAN by IPX network configuration table
snVLanByIpxNetFrameType
brcdIp.1.1.3.2.4.1.3
Syntax: Integer Read-only Shows the frame type for the Layer 3 VLAN:
•
notApplicable(0) – If none of the following options is selected
•
ipxEthernet8022(1)
•
ipxEthernet8023(2)
•
ipxEthernetII(3)
•
ipxEthernetSnap(4)
Each IPX Network Number must be assigned with one unique
Frame type; otherwise, an SNMP-SET error will be returned.
snVLanByIpxNetDynamic
brcdIp.1.1.3.2.4.1.4
Syntax: Integer Read-write Applies only to switches. Indicates whether or not dynamic port
inclusion is enabled:
•
disabled(0)
•
enabled(1)
snVLanByIpxNetStaticMask
brcdIp.1.1.3.2.4.1.5
Syntax: PortMask Read-write Shows the VLAN by IPX network port membership applied in static
mode.
snVLanByIpxNetExcludeMask
brcdIp.1.1.3.2.4.1.6
Syntax: PortMask Read-write Shows the VLAN by IPX network port membership applied in
exclusive mode.
snVLanByIpxNetRouterIntf
brcdIp.1.1.3.2.4.1.7
Syntax: Integer Read-write Applies only to routers and is optional. It shows the virtual interface
of a router to the VLAN.
Valid values: 0 – 60; however, this object is not configured if an
SNMP-Get is equal to zero.
snVLanByIpxNetRowStatus
brcdIp.1.1.3.2.4.1.8
Syntax: Integer Read-write Controls the management of the table rows. The following values
can be written:
•
delete(3) – Deletes the row.
•
create(4) – Creates a new row.
•
modify(5) – Modifies an existing row.
If the row exists, then a SET with a value of create(4) returns a "bad
value" error. Deleted rows are removed from the table immediately.
The following values can be returned on reads:
•
noSuch(0) – No such row.
•
invalid(1) – Row is inoperative.
•
valid(2) – Row exists and is valid.
snVLanByIpxNetDynamicMask
brcdIp.1.1.3.2.4.1.9
Syntax: PortMask Read-only Shows the VLAN by IPX network active port membership.
snVLanByIpxNetChassisStatic
Mask
brcdIp.1.1.3.2.4.1.10
Syntax: OCTET STRING Read-write This object has 32 octets and it is replaced by
“snVLanByIpxNetStaticPortList” .
Shows the chassis VLAN by IPX network port membership applied
in static mode.
snVLanByIpxNetChassisExclud
eMask
brcdIp.1.1.3.2.4.1.11
Syntax: OCTET STRING Read-write This object has 32 octets and it is replaced by
“snVLanByIpxNetExcludePortList” .
Shows the chassis VLAN by IPX network port membership applied
in exclusive mode.
snVLanByIpxNetChassisDyna
micMask
brcdIp.1.1.3.2.4.1.12
Syntax: OCTET STRING Read-only This object has 32 octets and it is replaced by
“snVLanByIpxNetDynamicPortList” .
Shows the chassis VLAN by IPX network port membership.
Name, OID, and syntax Access Description