Brocade Unified IP MIB Reference (Supporting FastIron Release 07.5.00) - Manual (Page 62)

34 Unified IP MIB Reference
53-1002549-02
RFC 3176: InMon Corporation’s sFlow: A Method for Monitoring Traffic in Switched and Routed Networks
RFC 3176: InMon Corporation’s sFlow: A Method for
Monitoring Traffic in Switched and Routed Networks
RFC 3176 MIBs enable you to configure the sFlow Export feature. Support for this RFC is available
on the following devices:
• Brocade NetIron MLX devices
• Brocade MLXe devices
• Brocade NetIron XMR
• Brocade NetIron CES and Brocade NetIron CER series devices
The following groups from RFC 3176 are supported in the devices.
Object Object identifier Supported?
pimComponentIndex 1.3.6.1.3.61.1.1.12.1.1 Yes
pimComponentBSRAddress 1.3.6.1.3.61.1.1.12.1.2 Yes, but read-only.
pimComponentBSRExpiryTime 1.3.6.1.3.61.1.1.12.1.3 Yes, but read-only.
pimComponentCRPHoldTime 1.3.6.1.3.61.1.1.12.1.4 Yes, but read-only.
pimComponentStatus 1.3.6.1.3.61.1.1.12.1.5 Yes, but read-only. Returns “active”.
Object Object identifier Description
sFlowAgent 1.3.6.1.4.1.4300.1.1 The sFlow agent sampler.
sFlowVersion 1.3.6.1.4.1.4300.1.1.1 Returns a version string (for
example, “1.2; Brocade”).
sFlowAgentAddressType 1.3.6.1.4.1.4300.1.1.2 Returns value 1 (IPv4).
sFlowAgentAddress 1.3.6.1.4.1.4300.1.1.3 Management IP.
sFlowTable 1.3.6.1.4.1.4300.1.1.4 sFlow Table.
sFlowDataSource 1.3.6.1.4.1.4300.1.1.4.1.1 ifIndex of sFlow port.
sFlowOwner 1.3.6.1.4.1.4300.1.1.4.1.2 Always null. Not supported in the
CLI.
sFlowTimeout 1.3.6.1.4.1.4300.1.1.4.1.3 Always 0. Not supported in the CLI.
sFlowPacketSamplingRate 1.3.6.1.4.1.4300.1.1.4.1.4 Port sampling rate. Set this value to
0 to disable sFlow for a port.
sFlowCounterSamplingInterval 1.3.6.1.4.1.4300.1.1.4.1.5 Global counter poll interval.
sFlowMaximumHeaderSize 1.3.6.1.4.1.4300.1.1.4.1.6 Always 128.
sFlowMaximumDatagramSize 1.3.6.1.4.1.4300.1.1.4.1.7 Always 1400.
sFlowCollectorAddressType 1.3.6.1.4.1.4300.1.1.4.1.8 Always 1 (IPv4).
sFlowCollectorAddress 1.3.6.1.4.1.4300.1.1.4.1.9 Address of first collector. For other
collectors, use
snSflowCollectorTable. (Refer to
“sFlow collector table” on
page 290.)