Sndvmrpgraftretransmitti me, Sndvmrpdefaultroute, Dvmrp virtual interface table – Brocade Unified IP MIB Reference (Supporting FastIron Release 07.5.00) User Manual

Page 577: Sndvmrpvinterfacetable, Sndvmrpvinterfacevifindex, Sndvmrpvinterfacetype, Sndvmrpvinterfaceoperstate, Sndvmrpvinterfacelocaladdress, Sndvmrpvinterfaceremoteaddress

Advertising
background image

Unified IP MIB Reference

549

53-1002549-02

DVMRP virtual interface table

DVMRP virtual interface table

The DVMRP virtual interface table contains the router’s DVMRP virtual interfaces.

NOTE

The following table is not supported on the Brocade MLXe router, Brocade NetIron MLX, Brocade
NetIron XMR, Brocade NetIron CES, and Brocade NetIron CER series devices.

snDvmrpGraftRetransmitTi
me
brcdIp.1.2.5.1.11
Syntax: Integer

Read-write

Defines how long a router that is sending a graft message will wait for
the first graft acknowledgement from an upstream router before
retransmitting that message. Subsequent retransmissions are sent at
an interval twice that of the preceding interval.
For NetIron platforms:

Valid values: 5 – 3600 seconds

Default: 10 seconds

For FastIron platforms:

Valid values: 2 – 10 seconds

Default: 3 seconds

snDvmrpDefaultRoute
brcdIp.1.2.5.1.12
Syntax: IpAddress

Read-write

This is the IP address of a router that is connected to one of the directly
attached subnets. If a multicast route is not present on the local router,
this default route will be used for multicast forwarding. The

“snDvmrpEnable”

object must be set to “enabled” before this object

can be written.

Name, OID, and syntax

Access

Description

Name, OID, and syntax

Access

Description

snDvmrpVInterfaceTable
brcdIp.1.2.5.1.13

None

The DVMRP virtual interface table.

snDvmrpVInterfaceVifIndex
brcdIp.1.2.5.1.13.1.1
Syntax: Integer

Read-only

The ifIndex value of this DVMRP virtual interface.

snDvmrpVInterfaceType
brcdIp.1.2.5.1.13.1.2
Syntax: Integer

Read-write

Indicates the type of this DVMRP virtual interface:

tunnel(1) – Tunnel interface, for which the interface is a
querier.

queries(2) – Tunnel interface, for which the interface is
not a querier.

subnet(3) – Physical interface, for which the interface is
not a querier.

snDvmrpVInterfaceOperState
brcdIp.1.2.5.1.13.1.3
Syntax: Integer

Read-only

Shows the current state of this DVMRP virtual interface:

up(1)

down(2)

snDvmrpVInterfaceLocalAddress
brcdIp.1.2.5.1.13.1.4
Syntax: IpAddress

Read-write

Shows the IP address of the local end of this DVMRP virtual
interface.

snDvmrpVInterfaceRemoteAddress
brcdIp.1.2.5.1.13.1.5
Syntax: IpAddress

Read-write

Shows the IP address of the remote end of this DVMRP virtual
interface.
For a tunnel, enter the IP address of the neighboring router.
For a subnet, enter the subnet address.

Advertising