Rockwell Automation 2364F Regenerative DC Bus Supply Unit (RGU) - Manual (Page 181)

Publication 2364F-5.01– October 2003
Programming Parameters D-37
179
Fault/Warning Select Mask 2
[Fault/Warn Mask2]
This parameter determines whether conditions
should be reported as a warning (0) or handled as
a fault (1).
The factory default, for example, shows that
all the usable bits cause faults.
Parameter Type Sink (Read/Write)
Display Units None
Drive Units Display Units * 1
Factory Default 1001 1100 0111 1111
Minimum Value 0000 0000 0000 0000
Maximum Value 1111 1111 1111 1111
Related Parameters P174, P176
Bit Description Bit Description
0* Desaturizatn Selects response to desaturization condition. 8 Not Used
1* Board Intlk Selects response to a board interlock condition. 9 Not Used
2* HW Bus OverV Selects response to bus overvoltage (hardware). 10* SW Line I Selects response to line current condition (software).
3* HW Line I Selects response to current condtn (hardware). 11* I Offset Err Selects response to current offset error.
4* Zero Seq Err Selects response to zero sequence error. 12* DualPort TO Selects response to dual port timeout.
5* Phase Lock L Selects response to phase lock loop condition. 13 Not Used
6* Phase Loss Selects response to phase loss in AC line. 14 Not Used
7 Not Used 15* DSP Fault Selects response to DSP fault.
* These items cannot be changed to zero.
180
Host Fault Status Word 3
[Fault Status 3]
This parameter indicates a number of host fault
conditions.
1 - Fault 0 - No Fault
Parameter Type Source (Read Only)
Display Units None
Drive Units Display Units * 1
Factory Default 0000 0000 0000 0000
Minimum Value 0000 0000 0000 0000
Maximum Value 1111 1111 1111 1111
Related Parameters P181, P182
P181 and P182 determine what conditions are
reported and how the conditions are to be
handled (warning/fault).
Bit Description
0 Clock Loss Indicates that a reset has occurred due to loss of oscillator.
1 Double Bus Indicates a memory access error.
2 Watchdog Indicates a expiration fault in the watchdog timer.
3 En at Pwr Up Indicates that the RGU was Enabled at power up.
4 Battery Low Indicates that the battery for the battery-backed memory is low.
5 TIO Loss Indicates that the primary control loop clock has been lost.
6 R2R Dup Addr Indicates that more than one RGU (in a parallel application) have the same R2R transmit address (P267).
7 Lost Master Indicates that communication to the master has been lost.
8 DPRAM Error Indicates a fault in the dual port between the host and DSP.
9 No Vloop Tic Indicates that the voltage loop clock has been lost.
10 No Fast Task Indicates that high speed control tasks have stopped.
11 No Bgnd Task Indicates that background tasks are not executing.
12 Addr Bus Err Indicates an error in the address bus.
13 Data Bus Err Indicates an error in the data bus.
14 Line Low Indicates that the AC line voltage has dropped below the AC Line Low Setting (P26).
15 Line High Indicates that the AC line voltage has exceeded the AC Line High Setting (P27).
Bit
8
Bit
9
Bit
10 Bit
11 Bit
12 Bit
13 Bit
14 Bit
15 Bit
0
Bit
1
Bit
2
Bit
3
Bit
4
Bit
5
Bit
6
Bit
7
Bit
8
Bit
9
Bit
10 Bit
11 Bit
12 Bit
13 Bit
14 Bit
15 Bit
0
Bit
1
Bit
2
Bit
3
Bit
4
Bit
5
Bit
6
Bit
7