Rockwell Automation 2364F Regenerative DC Bus Supply Unit (RGU) - Manual (Page 182)

Publication 2364F-5.01– October 2003
D-38 Programming Parameters
181
Fault Status 3 Report Mask
[Flt Report Mask 3]
This parameter selects the faults that can be
reported to P180.
1 - Report 0 - Suppress
Parameter Type Sink (Read/Write)
Display Units None
Drive Units Display Units * 1
Factory Default 1111 1111 1111 1111
Minimum Value 0000 0000 0000 0000
Maximum Value 1111 1111 1111 1111
Related Parameters P180, P181
Bit Description Bit Description
0 Clock Loss Reports when the oscillator clock is lost. 8* DPRAM Error Reports errors in the DPRAM.
1 Double Bus Reports memory access errors. 9 No Vloop Tic Reports when the voltage loop clock is lost.
2 Watchdog Reports when the watchdog timer is expired. 10* No Fast Task Reports when high speed tasks are not executing.
3 En at Pwr Up Reports when the RGU is Enabled at power up. 11* No Bgnd Task Reports when background tasks are not running.
4 Battery Low Reports when the BRAM battery is low. 12* Addr Bus Err Reports address bus errors.
5* TIO Loss Reports when the primary clock is lost. 13* Data Bus Err Reports data bus errors.
6* R2R Dup Addr Reports when RGUs have an address conflict. 14 Line Low Reports when the AC line voltage falls below P26.
7* Lost Master Reports when Master communication is lost. 15 Line High Reports when the AC line voltage exceeds P27.
* These items cannot be changed to zero.
182
Fault/Warning Select Mask 3
[Fault/Warn Mask3]
This parameter determines whether conditions
should be reported as a warning (0) or handled as
a fault (1).
Parameter Type Sink (Read/Write)
Display Units None
Drive Units Display Units * 1
Factory Default 0011 1101 1110 1000
Minimum Value 0000 0000 0000 0000
Maximum Value 1111 1111 1111 1111
Related Parameters P180, P181
Bit Description Bit Description
0 Clock Loss Selects response to a lost clock. 8* DPRAM Error Selects response to DPRAM errors.
1 Double Bus Selects response to memory access errors. 9 No Vloop Tic Selects response to voltage loop timer errors.
2 Watchdog Selects response to watchdog timer expiration. 10* No Fast Task Selects response to fast task lockup.
3 En at Pwr Up Selects response when RGU Enables at pwr up. 11* No Bgnd Task Selects response to background task lockup.
4 Battery Low Selects response to low BRAM battery voltage. 12* Addr Bus Err Selects response to address bus errors.
5* TIO Loss Selects response to primary clock being lost. 13* Data Bus Err Selects response to data bus errors.
6* R2R Dup Addr Selects response to duplicate address errors. 14 Line Low Selects response to low voltage in the AC line.
7* Lost Master Selects response to losing the Master. 15 Line High Selects response to high voltage in the AC line.
* These items cannot be changed to zero.
Bit
8
Bit
9
Bit
10 Bit
11 Bit
12 Bit
13 Bit
14 Bit
15 Bit
0
Bit
1
Bit
2
Bit
3
Bit
4
Bit
5
Bit
6
Bit
7
Bit
8
Bit
9
Bit
10 Bit
11 Bit
12 Bit
13 Bit
14 Bit
15 Bit
0
Bit
1
Bit
2
Bit
3
Bit
4
Bit
5
Bit
6
Bit
7