NXP Semiconductors LPC24XX UM10237 - Manual (Page 173)

UM10237_4 © NXP B.V. 2009. All rights reserved.
User manual Rev. 04 — 26 August 2009 173 of 792
NXP Semiconductors
UM10237
Chapter 8: LPC24XX Pin configuration
P4[21]/A21/
SCL2/SSEL1 115 [1] M15 [1] I/O P4[21] — General purpose digital input/output pin.
I/O A21 — External memory address line 21.
I/O SCL2 — I 2 C2 clock input/output (this is not an open-drain pin).
I/O SSEL1 — Slave Select for SSP1.
P4[22]/A22/
TXD2/MISO1 123 [1] K14 [1] I/O P4[22] — General purpose digital input/output pin.
I/O A22 — External memory address line 22.
O TXD2 — Transmitter output for UART2.
I/O MISO1 — Master In Slave Out for SSP1.
P4[23]/A23/
RXD2/MOSI1 129 [1] J15 [1] I/O P4[23] — General purpose digital input/output pin.
I/O A23 — External memory address line 23.
I RXD2 — Receiver input for UART2.
I/O MOSI1 — Master Out Slave In for SSP1.
P4[24]/OE 183 [1] B8 [1] I/O P4[24] — General purpose digital input/output pin.
O OE — LOW active Output Enable signal.
P4[25]/WE 179 [1] B9 [1] I/O P4[25] — General purpose digital input/output pin.
O WE — LOW active Write Enable signal.
P4[26]/BLS0 119 [1] L15 [1] I/O P4[26] — General purpose digital input/output pin.
O BLS0 — LOW active Byte Lane select signal 0.
P4[27]/BLS1 139 [1] G15 [1] I/O P4[27] — General purpose digital input/output pin.
O BLS1 — LOW active Byte Lane select signal 1.
P4[28]/BLS2/
MAT2[0]/LCDVD[6]/
LCDVD[10]/
LCDVD[2]/
TXD3 170 [1] C11 [1] I/O P4 [28] — General purpose digital input/output pin.
O BLS2 — LOW active Byte Lane select signal 2.
O MAT2[0] — Match output for Timer 2, channel 0. [19]
O LCDVD[6]/LCDVD[10]/LCDVD[2] — LCD data. [19]
O TXD3 — Transmitter output for UART3.
P4[29]/BLS3/
MAT2[1]
LCDVD[7]/
LCDVD[11]/
LCDVD[3]/RXD3 176 [1] B10 [1] I/O P4[29] — General purpose digital input/output pin.
O BLS3 — LOW active Byte Lane select signal 3.
O MAT2[1] — Match output for Timer 2, channel 1. [19]
O LCDVD[7]/LCDVD[11]/LCDVD[3] — LCD data. [19]
I RXD3 — Receiver input for UART3.
P4[30]/CS0 187 [1] B7 [1] I/O P4[30] — General purpose digital input/output pin.
O CS0 — LOW active Chip Select 0 signal.
P4[31]/CS1 193 [1] A4 [1] I/O P4[31] — General purpose digital input/output pin.
O CS1 — LOW active Chip Select 1 signal.
ALARM 37 [8] N1 [8] O ALARM — RTC controlled output. This is a 1.8 V pin. It goes HIGH when
a RTC alarm is generated.
USB_D
−2
52 U1 I/O USB_D
−2 — USB port 2 bidirectional D− line.
DBGEN 9 [1] F4 [1] I DBGEN — JTAG interface control signal. Also used for boundary
scanning.
TDO 2 [1] D3 [1] O TDO — Test Data Out for JTAG interface.
TDI 4 [1] C2 [1] I TDI — Test Data In for JTAG interface.
Table 124. LPC2470/78 pin description …continued
Symbol Pin Ball Type Description