Texas Instruments MSP430x1xx - Manual (Page 198)

T
imer Modes
1
1-22
T
imer_B
Table 11–2. Shadow Register Operating Modes (Continued)
TBCLGRP
CLLDx From
Lowest
CCTLx in
Counter
Mode
Load Conditions
TBCLGRP CCTLx in
Group (see
Note 1)
Mode
MCx
0 1 2 3 4 5 6
0 0–3 Immediate
TBCL1, TBCL2, TBCL3 loaded immediately when the
corresponding CCRx register is loaded
TBCL4, TBCL5, TBCL6 loaded immediately when the
corresponding CCRx register is loaded
1 1–3 TBR counts to 0
TBCL1, TBCL2, TBCL3 updated simultaneously when
TBR counts to 0
TBCL4, TBCL5, TBCL6 updated simultaneously when
TBR counts to 0
2
2
1,2 TBR counts to 0
TBCL1, TBCL2, TBCL3 updated simultaneously when
TBR counts to 0
TBCL4, TBCL5, TBCL6 updated simultaneously when
TBR counts to 0
2
3
TBR counts to 0
or to TBCL0
TBCL1, TBCL2, TBCL3 updated simultaneously when
TBR counts to 0 or to TBCL0
TBCL4, TBCL5, TBCL6 updated simultaneously when
TBR counts to 0 or to TBCL0
3 1–3
TBR counts to
TBCL0
TBR counts to
TBCL1
TBR counts to
TBCL2
TBR counts to
TBCL3
TBR counts to
TBCL4
TBR counts to
TBCL5
TBR counts to
TBCL6
0 0–3 TBCL0, TBCL1, TBCL2, TBCL3, TBCL4, TBCL5, TBCL6 Loaded immediately when the corresponging CCRx register is loaded.
1 1–3 TBCL0,TBCL1, TBCL2, TBCL3, TBCL4, TBCL5, TBCL6 updated simultaneously when TBR counts to 0
3
2
1,2 TBCL0,TBCL1, TBCL2, TBCL3, TBCL4, TBCL5, TBCL6 updated simultaneously when TBR counts to 0
3
2
3 TBCL0,TBCL1, TBCL2, TBCL3, TBCL4, TBCL5, TBCL6 updated simultaneously when TBR counts to 0 or to TBCL0
3 1–3
TBR counts to
TBCL0
TBR counts to
TBCL1
TBR counts to
TBCL2
TBR counts to
TBCL3
TBR counts to
TBCL4
TBR counts to
TBCL5
TBR counts to
TBCL6
Notes: 1) When using groups, load mode for the group is selected with the CLLDx bits of the lowest numbered CCTLx register in the group (except when TBCLGRP=3). For example,
when grouped by 2, the CLLDx bits of CCTL3 determine the load mode for TBCL3 and TBCL4. When grouped by 3, the CLLDx bits of CCTL4 determine the load mode for
TBCL4, TBCL5, and TBCL6, etc. When TBCLGRP=3 the CLLDx bits from TBCTL1 are used.
2) When using groups, all CCRx registers must be updated with new data before the load will take place (except when using immediate mode), even if new data = old data.
When using immediate mode, each compare latch is updated immediately when its corresponding CCRx register is updated.
3) When using groups, different load modes may be selected for each group. For example, when grouped by 3, immediate mode may be selected (via CLLDx bits in CCTL1)
for TBCL1, TBCL2, and TBCL3, and mode 2 may be selected (via CLLDx bits in CCTL4) for TBCL4, TBCL5, and TBCL6.