Lenze 9400 - Manual (Page 618)

13 Diagnostics & fault analysis
13.7 Error messages of the operating system
618
Lenze · Servo-Inverter 9400 HighLine · Reference manual · DMS 10.0 EN · 11/2013 · TD05/06
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
0x0068001b 6815771 Electronic nameplate: Communication error Warning -
0x0078000a 7864330 Electronic nameplate: Data are incompatible Information -
0x007b0030 8060976 Electronic nameplate: Data loaded Information -
0x007b0039 8060985 Electronic nameplate: Data outside parameter limits Information -
0x007b0032 8060978 Electronic nameplate: Encoder protocol unknown Information -
0x007b0033 8060979 Electronic nameplate: Encoder signal unknown Information -
0x007b0031 8060977 Electronic nameplate: Not found Information -
0x007b003e 8060990 Encoder monitoring: Pulse deviation detected No response C00621
0x007b001b 8060955 Encoder: Open circuit Fault C00580
0x007b002c 8060972 EnDat encoder: Battery empty Information -
0x007b004f 8061007 EnDat encoder: Command error Information -
0x007b0050 8061008 EnDat encoder: Initial position error Information -
0x007b0026 8060966 EnDat encoder: Lamp error Information -
0x007b002b 8060971 EnDat encoder: Overcurrent Information -
0x007b0029 8060969 EnDat encoder: Overvoltage Information -
0x007b0028 8060968 EnDat encoder: Position error Information -
0x007b0027 8060967 EnDat encoder: Signal error Information -
0x007b004e 8061006 EnDat encoder: Transmission error Information -
0x007b002a 8060970 EnDat encoder: Undervoltage Information -
0x00910011 9502737 Error during initialisation System fault -
0x006a0002 6946818 Error during the update of inputs and outputs Fault -
0x006a0017 6946839 Error in control configuration System fault -
0x00750000 7667712 External error Fault C00581
0x007b002d 8060973 Failure of motor phase U No response C00597
0x007b002e 8060974 Failure of motor phase V No response C00597
0x007b002f 8060975 Failure of motor phase W No response C00597
0x006a0010 6946832 Faulty application parameter Fault -
0x006a0001 6946817 Faulty program download Fault -
0x008c0002 9175042 File DeviceCFG.dat is defective Fault -
0x008c0008 9175048 File DeviceCFG.dat is invalid Fault -
0x008c0005 9175045 File DeviceCFG.dat is missing Fault -
0x008c0001 9175041 File ProjectList.dat is defective Fault -
0x008c0007 9175047 File ProjectList.dat is invalid Fault -
0x008c0004 9175044 File ProjectList.dat is missing Fault -
0x008c0000 9175040 File ProjectSelection.dat is defective Fault -
0x008c0006 9175046 File ProjectSelection.dat is invalid Fault -
0x008c0003 9175043 File ProjectSelection.dat is missing Fault -
0x0068001a 6815770 Firmware has been changed Information -
0x0068001e 6815774 Firmware incompatible to control card System fault -
0x006a0000 6946816 General error in the application Fault -
0x00910003 9502723 Heartbeat not periodic System fault -
0x00770010 7798800 Heatsink: fan is defective Fault C00610
0x00770001 7798785 Heatsink: Overtemperature Fault -
0x00770000 7798784 Heatsink: Temperature > C00122 Warning C00582
0x0077000a 7798794 Heatsink: thermal detector is defective Fault C00588
0x007b003b 8060987 Hiperface encoder: Command error Information -
0x007b003d 8060989 Hiperface encoder: Initial position error Information -
0x007b003a 8060986 Hiperface encoder: Transmission error Information -
0x007b003c 8060988 Hiperface encoder: Unknown encoder Information -
0x00b80019 12058649 Homing mode not allowed Fault -
0x006a0006 6946822 IdleTask: Overflow Fault -
0x00790000 7929856 Incorrect device command transfer System fault -
hex dec Error message Response (Lenze setting) can be set in