Lenze 9400 - Manual (Page 936)

Index
936
Lenze · Servo-Inverter 9400 HighLine · Reference manual · DMS 10.0 EN · 11/2013 · TD05/06
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
CAN status DIP switch (C00348) 771
CAN SYNC application cycle (C01130) 835
CAN SYNC Rx identifier (C00367) 775
CAN sync transmission cycle time (C00369) 775
CAN SYNC Tx identifier (C00368) 775
CAN telegram and error counter (C00360) 774
CAN TPDO counter (C00343) 769
CAN TPDO1 mask byte x (C00311) 764
CAN TPDO2 mask byte x (C00312) 765
CAN TPDO3 mask byte x (C00313) 765
CAN TPDO4 mask byte x (C00314) 766
CAN TPDOx cycle time (C00356) 773
CAN TPDOx delay time (C00324) 768
CAN TPDOx identifier (C00320) 766
CAN TPDOx Tx mode (C00322) 767
CAN/EPL device type (C219) 760
Capacitor temperature (C00068) 738
Change Cam Data Point M (C02926) 908
Change Cam Data Point X (C02924) 908
Change Cam Data Point Y (C02925) 908
Change of the basic function 380
Change Pos Data Point X (C02964) 911
Change Pos Data Point Y (C02965) 911
Changing cam data via parameterisation 564
Check configuration (C225) 760
Clock 840
,
841
COB-ID 299
COB-ID EMCY (I-1014) 347
COB-ID SYNC message (I-1005) 343
Code number duplicated (error message) 677
Code refresh (error message) 632
Combination memory module/device not possible (error
message) 630
Combination MXI1/MXI2 not possible (error message) 629
Combination of module in MXI1/device not possible (error
message) 631
Combination of module in MXI2/device not possible (error
message) 631
Communication cycle period (I-1006) 344
Communication error between device and device module (error
message) 664
Communication task
Standstill > 3 s (error message) 681
Communication with module in MXI1 interrupted (error
message) 664
Communication with module in MXI2 interrupted (error
message) 665
Communication with safety module interrupted (error
message) 682
Config. analog input 1 (C00034) 735
Configure exception handling 290
ConnectTable active (error message) 675
Consumer heartbeat time (I-1016) 348
Cont Data Point Choice (C02943) 910
Cont Pos X0 (C02944) 910
Cont Pos X1 (C02945) 910
Cont Time (C02946) 910
Cont Track Choice (C02940) 909
Cont Type (C02941) 909
Control card
Supply voltage (24 V DC) too low (error message) 640
Control card is defect (error message) 624
,
626
Control card is defect (UB18 neg.) (error message) 646
Control card is defect (UB24) (error message) 646
Control card is defect (UB8) (error message) 646
Control card is defect (VCC15 neg.) (error message) 646
Control card is defect (VCC15) (error message) 646
Control card is defect (VCC5) (error message) 647
Control card is incompatible (error message) 627
Control mode (C02567) 858
Control of two motor brakes 551
Controlled operation (without feedback) 407
Controller
Clamp operation (error message) 662
Overload during acceleration phases (error message) 658
Pulse inhibit is active (error message) 641
Controller enabled (error message) 641
Controller in STO state (error message) 641
Controller inhibit by (source) (C00158) 750
Correction of the leakage inductance 201
Counter
Brake chopper overload (C01203) 839
DC bus overvoltage (C01205) 839
Heatsink overtemp. (C01208) 839
Housing overtemp. (C01209) 839
Internal (C01210) 840
Ixt overload (C01204) 839
Mains switching (C01206) 839
Power section overload (C01212) 840
CPU
Overtemperature (error message) 643
Temperature > C00126 (error message) 642
Thermal detector is defect (error message) 644
CPU temp. warning threshold (C00126) 745
CPU temperature (C00069) 738
Curr. control par. of C75 C76 (C2866) 903
Current (C02773) 892
Current contr. reset time (C00076) 739
Current controller gain (C00075) 739
Current setpoint filter 150
Cycle (C02536) 853
Cyclic task
Standstill > 60 s (error message) 681