HEIDENHAIN TNC 620 (81760x-02) ISO programming - Manual (Page 625)

TNC 620 | User's ManualDIN/ISO Programming | 2/2015
625
Index
3
3-D basic rotation..................... 479
3D compensation
Peripheral Milling.................... 422
3-D touch probes
Calibration.............................. 468
3-D view................................... 505
A
About this manual........................ 6
ACC.......................................... 373
Accessories................................ 89
Actual position capture............. 102
Adding comments............ 137, 139
Additional axes..................... 93, 93
Adjusting spindle speed........... 446
Align tool axis........................... 412
Angle functions........................ 297
Approach contour..................... 205
ASCII Files................................ 376
Automatic program start.......... 528
Automatic tool measurement... 171
B
Basic rotation........................... 476
Measuring in Manual Operation
mode...................................... 476
Behavior after reception of ETX 544
Block........................................ 104
Delete.................................... 104
Block Check Character............. 543
C
CAD Viewer.............................. 251
CAD viewer and DXF converter
screen layout............................ 250
Calculating with parentheses... 322
Calculation of circles................ 298
Calculator................................. 141
Chamfer................................... 218
Chatter Control......................... 373
Checking the axis positions...... 449
Circle........................ 222, 224, 230
Circle center............................. 220
Circular path..................... 221, 230
Code numbers......................... 540
Comparison.............................. 589
Compensating workpiece
misalignment
By measuring two points on a
straight surface...................... 475
Condition of RTS line............... 543
Connecting/removing USB devices.
132
Connector pin layout for data
interfaces................................. 574
Context-sensitive help.............. 156
Control panel.............................. 70
Conversational dialog............... 101
Copying program sections 105, 105
Corner rounding....................... 219
D
D14: Displaying error messages....
303
D18: Reading system data....... 311
D19: Transfer values to the
PLC.......................................... 320
D20: NC and PLC
synchronization......................... 320
D26: TABOPEN: Open a freely
definable table......................... 383
D27: TABWRITE: Write to a freely
definable table......................... 384
D28: TABREAD: Read from a freely
definable table......................... 385
D29: Transfer values to the
PLC.......................................... 321
D37 EXPORT............................ 321
Data Backup............................. 110
Data interface........................... 541
Connector pin layouts............ 574
Set up.................................... 541
Data output on the screen....... 310
Data transfer software............. 545
Data transfer speed....
541, 542, 542, 542, 542, 543, 543
Datum management................ 451
Datum setting.......................... 459
Without a 3-D touch probe..... 459
Datum table............................. 466
Transferring test results.......... 466
Defining local Q parameters..... 293
Defining nonvolatile Q parameters..
293
Defining the workpiece blank... 100
Depart contour......................... 205
Dialog....................................... 101
Directory.......................... 111, 115
Copy....................................... 118
Create.................................... 115
Delete.................................... 119
Displaying HTML files.............. 126
Displaying Internet files............ 126
Display screen............................ 69
Downloading help files............. 160
Dwell time....................... 386, 387
DXF converter.......................... 252
Selecting hole positions
Icon.................................. 265
Mouse area...................... 264
E
Enter spindle speed................. 180
Error messages................ 151, 151
Help with............................... 151
Ethernet interface.................... 547
Configuring............................. 547
Connecting and disconnecting
network drives....................... 131
Connection options................ 547
Introduction............................ 547
External access........................ 535
External data transfer
iTNC 530................................ 130
F
FCL........................................... 540
FCL function.............................. 11
Feature Content Level................ 11
Feed rate.................................. 445
Adjust..................................... 446
On rotary axes, M116............. 414
Feed rate factor for plunging
movements M103.................... 357
Feed rate in millimeters per spindle
revolution M136....................... 358
File
Create.................................... 115
File Management............. 108, 111
File Manager
Calling.................................... 113
File manager
Copying files.......................... 115
Copying tables....................... 117
Delete file.............................. 119
Directories.............................. 111
Copy................................. 118
Create.............................. 115
External data transfer............. 130
File
Create.............................. 115
File type................................. 108
File type
External file types............ 110
Function overview.................. 112
Overwriting files..................... 116
Protect file.............................. 122
Rename file.................... 121, 121
Selecting files......................... 114
Tagging files........................... 120
File status................................ 113
Filter for hole positions with DXF
data update.............................. 266
Firewall.................................
FK programming.............. 235, 235
Circular paths......................... 240
Fundamentals......................... 235
FK-Programming
Graphics................................. 237
FK programming
Initiating dialog....................... 238