Rockwell Automation SP600 AC Drive User Manual Version 1.0 - Manual (Page 9)

Contents VII
Figure 12.15 – PI Regulator.................................................................... 12-32
Figure 12.16 – PI Preload Value............................................................. 12-35
Figure 12.17 – PI Status (134)................................................................ 12-36
Figure 12.18 – Selecting Stop Mode B ................................................... 12-40
Figure 12.19 – Coast to Stop (Stop Mode A = 0).................................... 12-41
Figure 12.20 – Ramp Stop (Stop Mode A = 1) ....................................... 12-41
Figure 12.21 – Ramp to Hold (Stop Mode A = 2) ................................... 12-42
Figure 12.22 – DC Brake (Stop Mode A = 3).......................................... 12-42
Figure 12.23 – Selecting Bus Reg Mode B............................................. 12-46
Figure 12.24 – Protective Circuit for External Resistor Packages .......... 12-47
Figure 12.25 – Save OIM Ref (192)........................................................ 12-54
Figure 12.26 – Save MOP Ref (194) ...................................................... 12-55
Figure 12.27 – Configuring Digital Inputs for MOP Inc and MOP Dec.... 12-55
Figure 12.28 – Dyn UserSet Cnfg........................................................... 12-59
Figure 12.29 – DynUsrSetSel ................................................................. 12-60
Figure 12.30 – Drive Status 1 (209)........................................................ 12-61
Figure 12.31 – Drive Status 2 (210)........................................................ 12-62
Figure 12.32 – Drive Alarm 1 (211)......................................................... 12-63
Figure 12.33 – Drive Alarm 2 (212)......................................................... 12-63
Figure 12.34 – Start Inhibits (214) .......................................................... 12-64
Figure 12.35 – Dig In Status (216).......................................................... 12-65
Figure 12.36 – Dig Out Status (217) ....................................................... 12-66
Figure 12.37 – Status 1 @ Fault (227) ................................................... 12-68
Figure 12.38 – Status 2 @ Fault (228) ................................................... 12-68
Figure 12.39 – Alarm 1 @ Fault (229) .................................................... 12-69
Figure 12.40 – Alarm 2 @ Fault (230) .................................................... 12-69
Figure 12.41 – Fault Config 1 (238) ........................................................ 12-71
Figure 12.42 – Alarm Config 1 (259)....................................................... 12-72
Figure 12.43 – Drive Logic Rslt (271) ..................................................... 12-73
Figure 12.44 – Manual Mask (286) ......................................................... 12-74
Figure 12.45 – Stop Owner..................................................................... 12-75
Figure 12.46 – Manual Owner ................................................................ 12-75
Figure 12.47 – Data Received By the Drive From the Network .............. 12-76
Figure 12.48 – Data Sent By the Drive To the Network.......................... 12-78
Figure 12.49 – Anlg In Config (320)........................................................ 12-79
Figure 12.50 – Anlg In Sqr Root (321) .................................................... 12-80
Figure 12.51 – Analog Input Scaling Example........................................ 12-81
Figure 12.52 – Anlg Out Absolute (341) ................................................. 12-85
Figure 12.53 – Dig Out1 OffTime (383) .................................................. 12-97
Figure 12.54 – Dig Out2 OffTime (387) ................................................ 12-101
Figure 13.1 – Location of DC Bus Voltage Measuring Points................... 13-2
Figure 13.2 – Location of the Ready LED................................................. 13-3
Figure 13.3 – Sample Fault Screen on the LCD OIM ............................... 13-9
Figure 13.4 – Accessing the Fault Queue............................................... 13-24
Figure 13.5 – Sample Fault Queue Entry ............................................... 13-24
Figure 13.6 – Accessing the Fault Parameters....................................... 13-24
Figure 13.7 – Accessing the Drive Status Parameters ........................... 13-25
Figure 13.8 – Accessing the List of Changed Parameters...................... 13-25