Rockwell Automation 1336E IMPACT Adjustable Frequency AC Drive User Manual V 1-4.XX - Manual (Page 239)

Parameters 11-41
127 Clr Flt/Res Mask
You can use the lower byte of Clr Flt/Res Mask (bits 0 through 7)
to select which SCANport devices can issue a Reset Drive
command. You can use the higher byte (bits 8 through 15) to
select which SCANport devices can issue a Clear Faults
command. You can choose between:
0 = Disable control
1 = Enable control
The bits are defined as follows:
Parameter number 127
File:group Interface/Comm:SCANport Config
Parameter type linkable destination
Display bits
Factory default 11111111.11111111
Minimum value 00000000.00000000
Maximum value 11111111.11111111
Conversion 1 = 1
Refer to Chapter 8, Using the SCANport Capabilities, for more
information.
Bit Description
0 Reset L Opt
Let the L Option board control
resets.
1 Reset SP 1
Let SCANport device 1 control
resets.
2 Reset SP 2
Let SCANport device 2 control
resets.
3 Reset SP 3
Let SCANport device 3 control
resets.
4 Reset SP 4
Let SCANport device 4 control
resets.
5 Reset SP 5
Let SCANport device 5 control
resets.
Bit Description
6 Reset SP 6
Let SCANport device 6 control
resets.
7 Reset P197
Let Logic Cmd Input
(parameter 197) control resets.
8 ClrFlt L Opt
Let the L Option board control
clear fault commands.
9 ClrFlt SP 1
Let SCANport device 1 control
clear fault commands.
10 ClrFlt SP 2
Let SCANport device 2 control
clear fault commands.
11 ClrFlt SP 3
Let SCANport device 3 control
clear fault commands.
Bit Description
12 ClrFlt SP 4
Let SCANport device 4 control
clear fault commands.
13 ClrFlt SP 5
Let SCANport device 5 control
clear fault commands.
14 ClrFlt SP 6
Let SCANport device 6 control
clear fault commands.
15 ClrFlt P197
Let Logic Cmd Input
(parameter 197) control clear
fault commands.
128 Dir/Ref Owner
You can use the lower byte of Dir/Ref Owner (bits 0 through 7) to
see which SCANport device currently has exclusive control of the
reference changes. You can use the higher byte (bits 8 through
15) to see which SCANport device currently has exclusive control
of direction changes. You can choose between:
0 = Reference/direction input not present
1 = Reference/direction input present
The bits are defined as follows:
Parameter number 128
File:group Monitor Status:SCANport Status
Interface/Comm:SCANport Status
Parameter type source
Display bits
Factory default not applicable
Minimum value 00000000.00000000
Maximum value 11111111.11111111
Conversion 1 = 1
Refer to Chapter 8, Using the SCANport Capabilities, for more
information.
Bit Description
0 Refer L Opt
The L Option board owns the
reference command.
1 Refer SP 1
SCANport device 1 owns the
reference command.
2 Refer SP 2
SCANport device 2 owns the
reference command.
3 Refer SP 3
SCANport device 3 owns the
reference command.
4 Refer SP 4
SCANport device 4 owns the
reference command.
5 Refer SP 5
SCANport device 5 owns the
reference command.
Bit Description
6 Refer SP 6
SCANport device 6 owns the
reference command.
7 Refer P197
Logic Cmd Input (parameter 197)
owns the reference command.
8 Direct L Opt
The L Option board owns the
direct command.
9 Direct SP 1
SCANport device 1 owns the
direct command.
10 Direct SP 2
SCANport device 2 owns the
direct command.
Bit Description
11 Direct SP 3
SCANport device 3 owns the
direct command.
12 Direct SP 4
SCANport device 4 owns the
direct command.
13 Direct SP 5
SCANport device 5 owns the
direct command.
14 Direct SP 6
SCANport device 6 owns the
direct command.
15 Direct P197
Logic Cmd Input (parameter 197)
owns the direct command.