A, figure, Using the l option 5-5, Table 5.a available control functions – Rockwell Automation 1336E IMPACT Adjustable Frequency AC Drive User Manual V 1-4.XX User Manual
Page 87
Using the L Option
5-5
Table 5.A shows the available combinations. Figure 5.1 and
Figure 5.2 also show the available combinations.
Table 5.A
Available Control Functions
Control
Function
Input Mode
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1st Accel
●
1st Decel
●
2nd/1st Decel
1
●
2nd Accel
●
●
●
2nd Decel
●
●
Common
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
●
●
●
●
●
●
●
●
●
●
Enable
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
●
●
●
●
●
●
●
●
●
●
Flux Enable
●
●
●
Forward
● ●
●
●
●
Jog
●
● ●
●
Local
●
●
●
MOP Dn
2
●
● ●
●
●
●
●
●
MOP Up
●
● ●
●
●
●
●
●
Not Ext Fault
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
●
●
●
●
●
●
●
●
●
●
Not Stop, Clr
Flt
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
●
●
●
●
●
●
●
●
●
●
Proc Trim
●
●
●
●
Ramp
●
●
●
Reset
●
●
●
●
Reverse
● ●
●
●
●
Rev/Fwd
● ● ● ● ●
● ●
●
Run Fwd
● ● ● ● ●
●
●
●
●
●
Run Rev
● ● ● ● ●
●
●
●
●
●
Spd Sel 1
4
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
●
●
●
●
●
●
●
●
● ● ● ● ● ● ● ●
● ● ● ● ● ● ●
●
●
●
●
●
●
●
●
● ●
● ●
● ●
●
●
Spd/Trq 1
5
● ●
●
Spd/Trq 2
● ●
●
Spd/Trq 3
● ●
●
Start
● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ●
●
●
●
Status
●
Stop Type
●
●
●
Profile Enable
●
Step Trigger
●
●
Run Sequence
●
Position Hold
●
1 The L Option uses the first function (such as 1st Decel or Rev) when input is applied and the second function (such as 2nd Decel or Fwd)
when input is not applied.
2 In modes 5, 9, 10, and 15, the MOP value is not reset to 0 when you stop. In modes 27, 28, 29, and 30, the MOP value is reset to 0 when you stop.
3 The L Option has ownership of direction. No other device on SCANport can control the direction.
4 The L Option has ownership of reference if all three selects are not available.
5 The L Option controls Spd/Trq Mode Sel (parameter 68).
NOTE: All Functions are enabled when input is applied and disabled when not applied.