Rockwell Automation 1336E IMPACT Adjustable Frequency AC Drive User Manual V 1-4.XX - Manual (Page 415)

I-7
PTrim Preload, 11-22, B-11
PTrim Reference, 11-21, B-11
PTrim Select, 11-22, B-11
Pulse In Offset, 7-11 to 7-12, 11-39
Pulse In PPR, 7-11 to 7-12, 11-38
Pulse In Scale, 7-11 to 7-12, 11-38
Pulse In Value, 7-11 to 7-12, 11-39
PWM Frequency, 11-11
PwrUp Flt Status, 11-70
Ramp/ClFlt Owner, 11-43
Regen Power Lim, 11-27, 13-9, B-21
for bus regulator braking, 9-3
Relay Config 1, 7-10, 11-36
Relay Config 2, 7-10, 11-56
Relay Config 3, 7-10, 11-57
Relay Config 4, 7-10, 11-58
Relay Setpoint 1, 7-10, 11-37
Relay Setpoint 2, 7-10, 11-56
Relay Setpoint 3, 7-10, 11-57
Relay Setpoint 4, 7-10, 11-58
resetting to default, C-7
Rev Speed Limit, 11-20, 13-9, B-7
Run Inhibit Sts, 11-14
Scaled Spd Fdbk, 11-24
S-Curve Percent, 11-21, B-8
Service Factor, 11-11
Slave Torque %, 11-26, B-22
Slip Gain, 11-50, B-26
source explained, 6-12
SP 2 Wire Enable, 8-4, 11-54
SP An In1 Scale, 8-15, 11-44
SP An In1 Select, 8-15, 11-44
SP An In1 Value, 8-15, 11-44
SP An In2 Scale, 11-45
SP An In2 Select, 11-44
SP An In2 Value, 11-44
SP An Output, 8-15, 11-45
SP Enable Mask, 11-39
Spd Desired BW, 11-49, 13-10, 13-11, B-18
Spd Error, 11-72
Spd Reg Output, 11-72
Spd/Trq Mode Sel, 7-12, 11-26, B-22
Speed Ref 1, 11-18
Speed Ref 1 Frac, 11-18
Speed Ref 2, 11-18
Speed Ref 3, 11-18
Speed Ref 4, 11-18
Speed Ref 5, 11-19
Speed Ref 6, 11-19
Speed Ref 7, 11-19
Speed Scale 1, 11-18
Speed Scale 7, 11-19
Start Dwell Spd, 11-59, B-5
Start Dwell Time, 11-59, B-5
Start/Jog Mask, 11-40
Start/Stop Owner, 11-42
Stator Resistnce, 11-50
Stop Dwell Time, 11-14
Test Data 1, 11-31
check for fluxing time, 12-20
for calculated undervoltage, 12-19
for precharge status, 12-19
Test Data 2, 11-31
for math limit fault, 12-25 to 12-27
for parameter limit fault, 12-22
Test Select 1, 11-31
check for fluxing time, 12-20
for calculated undervoltage, 12-19
for precharge status, 12-19
Test Select 2, 11-32
for math limit fault, 12-25 to 12-27
for parameter limit fault, 12-22
Torque Limit Sts, 11-30, B-21
Torque Ref 1, 11-26, B-22
Total Inertia, 11-48, 13-10, 13-11
Trans Dgn Config, 11-51, 13-3
uploading profile, C-7
Vd Max, 11-51
Vq Max, 11-51
Warning Select 1, 8-7, 8-8, 11-16, 12-4 to 12-5, 12-18
Warning Select 2, 11-17, 12-24
Warning Status 1, 11-71
Warning Status 2, 11-72
Zero Speed Tol, 11-15
password, C-10
Pos Mtr Cur Lim, 9-7, 11-27, 13-9, B-22, B-23
Pos Torque Lim, 11-27, B-21, B-22
power
applying, 6-2
before applying, 6-1
connecting to drive, 2-25
input fusing, 2-27
requirements for frames A1 – A4, 3-4
requirements for frames B – G, 4-11
isolation-type transformer requirements, 2-27
line reactor requirements, 2-27
understanding limits, B-21
wiring, 2-17
frames A1 – A4, 3-1
frames B – G, 4-1
precharge
checking status of, 12-19
common bus, 11-12
configuring faults/warnings for, 12-18
disable multiple, 11-12
explained, 12-15
force exit, 11-12
options for, 11-12
timeout, 11-15, 11-16, 12-4, 12-18
process trim
enable, 11-22
explained, B-11
overview, B-10
preset integrator option, 11-22
PTrim Feedback, 11-21, B-11
PTrim Filter BW, 11-22
PTrim Hi Limit, 11-23, B-12
PTrim Ki, 11-22, B-11
PTrim Kp, 11-23, B-11