Rockwell Automation 1757-SWKIT5000 ProcessLogix R500.1 Installation and Upgrade Guide User Manual
Processlogix r500.1 installation and upgrade guide
Advertising
Table of contents
Document Outline
- 1757-IN500A-EN-P
- Important User Information
- Table of Contents
- Preface
- Chapter 1: ProcessLogix R500.1 Installation Introduction
- Chapter 2: Operating System Installation Procedures
- Clean System Windows 2000 Server Installation
- Clean System Windows 2000 Professional Installation
- Clean System Windows XP Professional Installation
- Upgrading Windows 2000 Professional to XP Professional
- Windows 2000 Service Pack 2 Installation
- Windows 2000 Security Rollup Installation
- Internet Explorer 6.0 Installation
- Internet Explorer 6.0 Security Update Installation
- Updating Windows Installer
- Additional Operating System Customization Procedures
- Creating an Emergency Repair Disk
- Creating the ProcessLogix User Accounts
- Chapter 3: ProcessLogix Server Installation Procedures
- Installing ProcessLogix Software on a Clean PC
- Installing ProcessLogix R500.1 Software
- Moving the RSLinx Activation File
- Configuring RSLinx Drivers for ControlNet Supervisory Network
- Configuring RSLinx Drivers for Ethernet Supervisory Network
- Completing the ProcessLogix R500.1 Install on a Redundant Server Pair
- Completing the ProcessLogix R500.1 Install on a Non-Redundant Server
- Chapter 4: ProcessLogix Server Upgrade Procedures
- ProcessLogix Server Upgrade Scenarios
- Preparing for a ProcessLogix R320.0 to R500.1 Server Upgrade
- Copying R320.0 Data to the R500.1 Server
- Transferring the 1784-PCIC Card to the R500.1 System
- Preparing for a ProcessLogix R400.0 to R500.1 Server Upgrade
- Saving R400.0 Data to a Remote PC
- Removing ProcessLogix R400.0 Software
- Installing ProcessLogix R500.1 Software
- Finalizing R400.0 to R500.1 Upgrade
- Restoring ProcessLogix Data
- Chapter 5: ProcessLogix Client Installation and Upgrade Procedures
- Introduction
- Operating System Support
- Windows 2000 Professional Client Installation Scenarios
- Clean Install: Windows 2000 Professional
- Upgrade R400.0 Windows 2000 Professional Client to R500.1 Windows 2000 Professional Client
- Upgrade R400.0 Windows NT 4.0 Client to R500.1 Windows 2000 Professional Client (Clean Install)
- Upgrade R320.0 Windows NT 4.0 Client to R500.1 Windows 2000 Professional Client (Clean Install)
- Windows XP Professional Client Installation Scenarios
- Saving Important Data
- Networking an R320.0 Client to a Remote PC
- Networking an R400.0 Client to a Remote PC
- Removal of Selected R400.0 Components
- Installing ProcessLogix R500.1 Client Software
- Finalizing ProcessLogix Client Installation
- Transferring R320.0 Data to the R500.1 Client
- Transferring R400.0 Data to the R500.1 Client
- Restoring ProcessLogix Data
- Setting Up a Station With a Non-redundant Server
- Setting Up a Station With a Redundant Server Pair
- Creating an Emergency Repair Disk
- Checking Control Builder Operation and Logging On
- Chapter 6: Additional Redundant Server Procedures
- Adding Redundancy to R500.1 Non-Redundant Server Systems
- Completing the ProcessLogix R500.1 Setup on a Redundant Server Pair
- Setting up Primary Server (SERVERA)
- Setting Up Secondary Server (SERVERB)
- Configuring Stations in Quick Builder (on SERVERA)
- Setting Up Station on SERVERA
- Setting Up Station on SERVERB
- Setting up the Redundant ERDB
- Restarting Redundant Servers
- Synchronizing Server Databases on Redundant Server
- Upgrading Hardware Component Firmware
- Chapter 7: Firmware Maintenance Procedures
- 1784-PCIC Driver Installation
- 1784-PCIC Firmware Installation
- Upgrading Hardware Component Firmware
- About Firmware Upgrades
- Firmware Revision Level Reference
- Important Usage Considerations
- Loading 1757-PLX52, TC-MUX021, or 1757-FIM Boot and Personality Images
- Updating Firmware in CNB, ENET, IOM, SRM, PIM or ControlNet Adapter
- Redundant Chassis Firmware Upgrade Precautions
- Setting CNB Module NUT Timing
- Updating Firmware in ABRIO
- Chapter 8: Supplementary Procedures
- Stopping ProcessLogix Applications and Services
- Installing Knowledge Builder on a Non-ProcessLogix System
- Launching ProcessLogix Knowledge Builder
- SQL Server
- Cancelling a Software Component Installation
- Manual System Backup/Restore Procedures
- Using Network Tools
- Installing and Running NetShield with ProcessLogix
- Changing the Computer Name on a ProcessLogix Server
- Exporting the Engineering Repository Database
- Stopping ProcessLogix Applications and Services
- Removing Selected ProcessLogix R500.1 Components
- Remove ProcessLogix R500.1 Server Components
- Verifying and Finalizing Component Removal
- Changing the PC Name
- PC Naming Rules
- Reinstalling ProcessLogix R500.1 Components
- Restoring the Data
- Changing the Computer Name on a ProcessLogix Client
- Adding 1757-PLX52 Controller Redundancy to R500.1 Non-Redundant 1757-PLX52 Controller Configurations
- Chapter 9: New Functions and Features
- Engineering Tools Enhancements
- Server Enhancements
- Hardware Enhancements
- Chapter 10: Major ProcessLogix Software Components
- Chapter 11: Performance and Capacity Specifications
- Server/Client Performance and Capacity
- Controller and Communications Capacity and Performance
- I/O Performance and Capacity Specifications
- Special Considerations
- How Are We Doing?
- Backcover