Rockwell Automation Liqui-Flo DBT Reach Drive - Manual (Page 243)

Index Index-5
Motor NP FLA (42), 3-7
Motor NP Hertz (43), 3-8
Motor NP Power (45), 3-8
Motor NP RPM (44), 3-8
Motor NP Volts (41), 3-7
Motor OL Count (220), 3-64
Motor OL Factor (48), 3-9
Motor OL Hertz (47), 3-9
Motor Overload, D-3
Motor Poles (49), 3-9
Motor Sheave (645), 3-123
Motor Type (40), 3-7
Mtr NP Pwr Units (46), 3-8
Mtr OL Trip Time (221), 3-64
Mtr Tor Cur Ref (441), 3-111
N
Neg Torque Limit (437), 3-110
Notch Filter Freq (419), 3-106
Notch Filter K (420), 3-106
O
OilWell, 3-122
OilWell Pump Sel (641), 3-122
Output Current (3), 3-2
Output Freq (1), 3-2
Output Power (7), 3-3
Output Powr Fctr (8), 3-3
Output Voltage (6), 3-3
Overspeed, D-4
Overspeed Limit (83), 3-18
P
Param Access Lvl (196), 3-53
Parameter Linking, C-8
PCP, 3-121
PCP Pump Sheave (637), 3-121
PE Ground, 2-4
Phase V Amps (23), 3-5, 3-6, 3-20
PI BW Filter (139), 3-36
PI Configuration (124), 3-29
PI Control (125), 3-30
PI control, about, 3-31
PI Deriv Time (459), 3-113
PI Error Meter (137), 3-36
PI Fdback Meter (136), 3-36
PI Feedback Hi (462), 3-113
PI Feedback Lo (463), 3-113
PI Feedback Sel (128), 3-33
PI Integral Time (129), 3-33
PI Lower Limit (131), 3-34
PI Output Gain (464), 3-114
PI Output Meter (138), 3-36
PI Preload (133), 3-34
PI Prop Gain (130), 3-34
PI Ref Meter (135), 3-35
PI Reference Hi (460), 3-113
PI Reference Lo (461), 3-113
PI Reference Sel (126), 3-32
PI Setpoint (127), 3-32
PI Status (134), 3-35
PI Upper Limit (132), 3-34
Port, 3-152
Port Mask Actv (595), 3-152
Ports, DPI Type, C-2
Pos Reg Filter (718), 3-131
Pos Reg Gain (719), 3-132
Pos Torque Limit (436), 3-109
Power Cables/Wiring, 2-5
Power Conditioning, Input, 2-2
Power Loss Level (186), 3-50
Power Loss Mode (184), 3-49
Power Loss Ride Through, D-5
Power Loss Time (185), 3-50
Power Up Marker (242), 3-69
Powerup Delay (167), 3-44
Preferences, Setting, C-5
Preset Speed 1 (101), 3-25
Preset Speed 2 (102), 3-25
Preset Speed 3 (103), 3-25
Preset Speed 4 (104), 3-25
Preset Speed 5 (105), 3-25
Preset Speed 6 (106), 3-25
Preset Speed 7 (107), 3-25
Process PI
Standard Control, D-7
Profile, 3-129, 3-130
Profile Command (705), 3-130
Profile Status (700), 3-129
PTC HW Value (18), 3-5
Pulse Input Ref (99), 3-25
Pulse ln Scale (422), 3-107
PWM, 3-144
PWM DAC Enable (513), 3-144
PWM Frequency (151), 3-39
PWM Type Select (524), 3-145