Siemens AC75 - Manual (Page 89)

AC75 AT Command Set
3.3 AT^SIND
s
AC75_ATC_V01.002 Page 89 of 569 10/30/06
Confidential / Released
manual network selection fails and the module automatically falls back to the
previous network the NITZ values cannot be recalled. Nevertheless an indi-
cated time zone is valid until a new MMI/GMMI will trigger another NITZ indi-
cation.
“simstatus“ SIM Status Indication
The SIM Status indicator allows the AC75 to output the status of the subscriber
identity module (SIM) via URC.
“band“ Currently selected frequency band or band combination.
“simlocal“ Availability of the SIM card, physically connected
If RSA is active: The
AT^SIND
"simlocal" URC refers to the unused local SIM.
The status of the remote SIM card currently used for the RSA connection is
controlled by
AT^SCKS
.
If RSA is inactive: The
AT^SIND
"simlocal" URC refers to the currently used
local SIM. In this case the value is identical to the
AT^SCKS
value, except for
AT^SCKS
value 2.
Integer type value in the range stated above for the corresponding
<indDescr>
.
Notes specific to the EONS feature:
If the indicator is "eons", the
<indValue>
is a type associated to the operator name according to GSM 22.101
[26] . This type depends on the source of the operator name.
Priority of types associated to the operator names is defined as follows (the type listed first has the highest pri-
ority). If a type cannot be indicated the next one will be used.
0 SIM card removed.
Note: Another way to verify the SIM card connection is the "
^SCKS
"
URC enabled with
AT^SCKS
. For use after restart, its presentation
mode can be stored to the user profile with
AT&W
.
1 SIM card inserted.
2 SIM PIN1 not required - SIM card unlocked. AC75 automatically regis-
ters to the GSM network without requesting SIM PIN1.
3 SIM PIN1 required - SIM card locked. SIM PIN1 must be entered to
enable AC75 to register to the GSM network.
4 Personalization info ready - CHV (Card Holder Verification) data have
been verified (if required).
5 SIM initialization completed - ME has finished reading SIM data.
Note: Another way to notify the user when SIM data are accessible is
the "
^SSIM READY
" URC enabled with
AT^SSET
. For use after restart,
its presentation mode can be stored to the user profile with
AT&W
.
1...12 Identical with
<rbc>
of
AT^SCFG
. The value indicates the band(s) cur-
rently available for network selection, depending on the network config-
uration either a single band or a dualband combination. The URC
appears whenever the status of the currently available band(s)
changes, for example after using the
AT^SCFG
command to change
the "Radio/Band" parameters
<rba>
or
<rbp>
. Please see
AT^SCFG
for further detail about the feature "Radio/Band" selection.
0 SIM removed.
1 SIM inserted.
<indValue>
(num)
0 Not registered.
1 EF-OPL and EF-PNN (alphanumeric format, can contain up to 24 characters.)
2 Operator Name String in long and short format according to Common PCN
Handset Specification (CPHS) [27] (alphanumeric format, can contain up to 16
characters).
3 Name information received by the NITZ service long and short form (alphanu-
meric format, can contain up to 16 characters). The short form will be displayed
only if EF
OPShort
from CPHS is available.
4 Any operator name stored internal to the ME (alphanumeric format, can con-
tain up to 16 characters).