Rockwell Automation 20P PowerFlex Digital DC Drive - Manual (Page 170)

170 Rockwell Automation Publication 20P-UM001I-EN-P - February 2013
Chapter 3 Programming and Parameters
UTILIT
Y
Fa
u
lt
s
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360 [Fault 1 Code]
[Fault 2 Code]
[Fault 3 Code]
[Fault 4 Code]
[Fault 5 Code]
[Fault 6 Code]
[Fault 7 Code]
[Fault 8 Code]
[Fault 9 Code]
[Fault 10 Code]
A code that represents the fault that tripped the drive. The codes will appear in
these parameters in the order they occur (i.e., [Fault 1 Code] = the most recent
fault). See Fault Descriptions on page
202 for a list of possible codes.
Note: Par 1351 [Fault 1 Code] is accessible via the Basic Parameter view.
Default:
Min/Max:
Read Only
0 / 32768
16-bit
Int
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370 [Fault 1 Time]
[Fault 2 Time]
[Fault 3 Time]
[Fault 4 Time]
[Fault 5 Time]
[Fault 6 Time]
[Fault 7 Time]
[Fault 8 Time]
[Fault 9 Time]
[Fault 10 Time]
The time between initial drive power up and the occurrence of the associated trip
fault.
Default:
Min/Max:
Units:
Read Only
0.000 / 134000000.000
hr.
Real
1371 [Fault Arm Amps]
Captures and displays the armature current (as a percentage of rated current) at
the time of the last fault.
Default:
Min/Max:
Units:
Read Only
–/+200
%
16-bit
Int
1372 [Fault Speed]
Captures and displays the output speed (rpm) of the drive at the time of the last
fault.
Default:
Min/Max:
Units:
Read Only
– / +8192
rpm
16-bit
Int
1373 [Fault Field Amps]
Captures and displays the field current (as a percentage of rated current) at the
time of the last fault.
Default:
Min/Max:
Units:
Read Only
0.00 / 100.00
%
Real
1374 [Fault Voltage]
Captures and displays the armature voltage at the time of the last fault.
Default:
Min/Max:
Units:
Read Only
- / + 999.00
Vdc
Real
Al
arms
203 [OverVolt Flt Cfg]
Determines the response of the drive to an overvoltage condition (F5 “Arm
Overvoltage”).
Note: See Chapter 4 for a list of alarm and fault descriptions.
Default:
Options:
2 =
0 =
1 =
2 =
“Fault”
“Ignore”
“Alarm”
“Fault”
16-bit
Int
354 [Aux Inp Flt Cfg]
Determines the response of the drive to an external fault condition (F2 “Auxiliary
Input”), i.e., no voltage at the digital input terminal assigned to [Digital Inx Sel]
with a value of 14 “Aux Fault”.
Notes: See Chapter 4 for a list of alarm and fault descriptions. Option 3 was
changed from “Quick Stop” to “Fast Stop” for firmware version 2.001.
Default:
Options:
2 =
1 =
2 =
3 =
4 =
5 =
“Fault”
“Alarm”
“Fault”
“Fast Stop”
“Normal Stop”
“CurrLim Stop”
16-bit
Int
Fil
e
Gr
oup
No
. Parameter Name & Description
See page 110 for symbol descriptions
Values Da
ta
T
yp
e
Rela
ted
A
A
A
ATTENTION: Setting this parameter to 0 “Ignore” or 1 “Alarm”, could result in motor and/or equipment damage. If set to
“Ignore” or “Alarm”, it is strongly recommended that an external means of protecting against this condition be provided.
A
ATTENTION: Setting this parameter to 1 “Alarm”, could result in motor and/or equipment damage. If set to “Alarm”, it is
strongly recommended that an external means of protecting against this condition be provided.