Resolver type selection, Resolver type selection o, Resolver type selection on – Rockwell Automation 20P PowerFlex Digital DC Drive User Manual
Page 283
Rockwell Automation Publication 20P-UM001I-EN-P - February 2013
283
Application Notes
Appendix C
10.
Monitor Par 426 [Resolver Status], bits 0 “CableBalSts” and 1
“CableBalTest”. The initial test typically takes approximately 10 seconds to
successfully complete (subsequent tests more quickly). However, if the
cable balance algorithm is unable to adapt to the cable, the test could be
active for up to 60 seconds.
•
For bit 0 “CableBalSts”: 1 = the cable is not balanced or the test is
currently active, and 0 = the cable is balanced (tuned).
•
For bit 1 “CableBalTest”: 0 = the cable balance (tuning) test is
completed, and 1 = the cable cannot be balanced or the motor was not
at minimum speed the during test.
11.
Stop the drive. If the cable balance test fails, verify that the resolver is
properly configured and connected to the drive. Repeat the test after
addressing any issues.
12.
Reconfigure Par 414 [Fdbk Device Type] to 4 “Resolver”.
Resolver Type Selection
The following table provides a description and related attributes for the resolver
types compatible with the PowerFlex DC drive and resolver feedback module.
Where possible, specific compatible resolver models have been identified.
Additional options are available for this parameter when a resolver with matching
attributes is used (identified by the option “Resolver xx”).
Table 89 - Resolver Type Attributes
Par 423 [Reslvr Type Sel] Option
Resolver Catalog Numbers
(Manufacturer)
(1)
Par 424 [Reslvr Spd
Ratio]
Carrier
Frequency
Input
Voltage
Transformer
Ratio
Feedback
Amp Gain
Power Amp
Voltage
1 “2014x1/AMCI”
800123-R, -1R, -2R (Rel)
TS-2014N181E32 (Tam)
TS-2087N1E9 (Tam)
TS-2087N11E9 (Tam)
R11X-C10/7 (Adv)
x1
2381
26
0.4538
0.5
45
2 “T2014x2/2087”
800123-S, -1S, -2S (Rel)
TS-2014N182E32 (Tam)
TS-2087N12E9 (Tam)
TS-2087N2E9 (Tam)
x2
2381
26
0.4538
0.5
45
3 “T2014x5/2087”
800123-T, 1T, 2T (Rel)
TS-2014N185E32 (Tam)
TS-2087N5E9 (Tam)
x5
2381
26
0.4538
0.5
45
4 “Resolver 04”
–
x2
4000
8
0.25
0.92
14
5 “Resolver 05”
–
x2
9300
22
0.5
0.5
45
6 “Resolver 06”
–
x1
4000
5
0.5
0.92
14
7 “Resolver 07”
–
x1
7000
4.25
0.4706
0.92
14
8 “Resolver 08”
–
x1
2500
12
0.5
0.5
45
9 “Resolver 09”
–
x2
4000
8
0.25
0.92
14
10 “Resolver 10”
–
x2
9300
15.5
0.5013
0.5
45
11 “Resolver 11”
–
x2
2500
7
1.7
0.5
45
12 “Resolver 12”
–
x2
9300
22
0.5
0.5
45
13 “Resolver 13”
–
x1
2000
6.36
0.5
0.92
14
14 “Resolver 14”
–
x1
6500
8
0.5
0.5
14
15 “Resolver 15”
–
x1
6500
8
0.5
0.5
14
(1)
Abbreviations in this column indicate the following resolver manufacturers: Adv = Advanced Micro Controls, Inc. (AMCI), Rel = Reliance (-x = foot mounted, -1x = foot mounted, double shaft, -2x = flange mounted), Tam =
Tamagawa.