Rockwell Automation 1771-QDC PLASTIC MOLD.MODULE - Manual (Page 12)

Table of Contents x
ID = 15 – PPC – Plastication Profile Block 4–33 . . . . . . . . . . . . . .
ID = 16 – PSC – Post-Decompression Configuration Block 4–38 . .
ID = 17 – FOC – First Clamp Open Configuration Block 4–39 . . . .
ID = 18 – SOC – Second Clamp Open Configuration Block 4–40 . .
ID = 19 – TOC – Third Clamp Open Configuration Block 4–42 . . . .
ID = 20 – OSC – Clamp Open Slow Configuration Block 4–43 . . . .
ID = 21 – OPC – Clamp Open Profile Block 4–44 . . . . . . . . . . . . .
ID = 22 – EAC – Ejector Advance Configuration Block 4–50 . . . . .
ID = 23 – ERC – Ejector Retract Configuration Block 4–51 . . . . . .
ID = 24 – EPC – Ejector Profile Block 4–52 . . . . . . . . . . . . . . . . .
ID = 25 – DYC – Dynamic Command Block 4–55 . . . . . . . . . . . . .
ID = 26 – RLC – Inject ERC Values Block 4–56 . . . . . . . . . . . . . .
ID = 27 – CLC– Clamp and Eject ERC Values Block 4–57 . . . . . . .
ID = 28 – PTC – Process Trace Configuration Block 4–57 . . . . . . .
Notes: 4–58 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Specifications 5–1 . . . . . . . . . . . . . . . . . . . . . . . .
I/O Specifications 5–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental Conditions 5–1 . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Requirements 5–1 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Process Control Options 5–2 . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibration Instructions 6–1 . . . . . . . . . . . . . . . . . . . . . . .
Calibration Equipment Required 6–1 . . . . . . . . . . . . . . . . . . . . .
About This Procedure 6–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Map Your BTW and BTR Data Blocks 6–2 . . . . . . . . . . . . . . . . .
Write Your Calibration Logic 6–2 . . . . . . . . . . . . . . . . . . . . . . . .
Set Internal Jumpers 6–3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wire the Wiring Arms 6–5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Wiring 6–5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Wiring 6–5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibration Setup Using Optional Equipment 6–6 . . . . . . . . . . . .
Calibration Setup at the Machine Location 6–6 . . . . . . . . . . . . . .
Calibration Procedure for Inputs 6–7 . . . . . . . . . . . . . . . . . . . . .
Calibration Procedure for Outputs 6–8 . . . . . . . . . . . . . . . . . . . .
Notes: 6–10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Single-transfer for Reporting Ejector Status A–1 . . . . . . .
How the Enhancement Effects System Operation A–1 . . . . . . . . .
Notes: A–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .