Rockwell Automation 1771-QDC PLASTIC MOLD.MODULE - Manual (Page 4)

Table of Contents ii
SOC – Second Clamp Open Configuration Block 1–32 . . . . . . . . .
TCC – Third Clamp Close Configuration Block 1–33 . . . . . . . . . . .
TOC – Third Clamp Open Configuration Block 1–35 . . . . . . . . . . .
CLS – Clamp and Eject ERC Values Status Block 1–36 . . . . . . . .
CPS – Clamp Close Profiles Status Block 1–37 . . . . . . . . . . . . . .
EPS – Ejector Profile Status Block 1–39 . . . . . . . . . . . . . . . . . . .
HPS – Pack/Hold Profile Status Block 1–40 . . . . . . . . . . . . . . . . .
IPS – Injection Profile Status Block 1–41 . . . . . . . . . . . . . . . . . . .
OPS – Clamp Open Profiles Status Block 1–42 . . . . . . . . . . . . . .
PPS – Plastication Profile Status Block 1–44 . . . . . . . . . . . . . . . .
PTS – Process Trace Status Block 1–45 . . . . . . . . . . . . . . . . . . .
RLS – Inject ERC Values Status Block 1–46 . . . . . . . . . . . . . . . . .
SYS - System Status Block 1–47 . . . . . . . . . . . . . . . . . . . . . . . .
Command Word/Bit Descriptions 2–1 . . . . . . . . . . . . . . . .
Alphabetical List of Command Blocks and Block ID Codes 2–1 . .
List of Data Words 2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Block ID Word 2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bit-mapped Words 2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stored-value Words 2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Open Words 2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reserved Words 2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engineering Units 2–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Blocks Require I/O Configuration 2–3 . . . . . . . . . . . . . . . . .
Data Blocks for System Control 2–4 . . . . . . . . . . . . . . . . . . . . .
Data Blocks for Controlling Ram (Screw) Position 2–4 . . . . . . . . .
Data Blocks for Controlling Clamp Position 2–5 . . . . . . . . . . . . .
Data Blocks for Controlling Ejector Position 2–5 . . . . . . . . . . . . .
Sensors Required 2–6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLC – Clamp and Eject ERC Values Block 2–7 . . . . . . . . . . . . .
Bit-mapped Control Words 2–7 . . . . . . . . . . . . . . . . . . . . . . .
Clamp Close Profiles ERC Values 2–7 . . . . . . . . . . . . . . . . . .
Clamp Open Profiles ERC Values 2–7 . . . . . . . . . . . . . . . . . .
Ejector Profile ERC Values 2–7 . . . . . . . . . . . . . . . . . . . . . . .
CPC – Clamp Close Profile Block 2–8 . . . . . . . . . . . . . . . . . . . .
Bit-mapped Control Words 2–8 . . . . . . . . . . . . . . . . . . . . . . .
First Clamp Close Profile Setpoints 2–10 . . . . . . . . . . . . . . . . .
Second Clamp Close Profile Setpoints 2–10 . . . . . . . . . . . . . . .
Third Clamp Close Profile Setpoints 2–11 . . . . . . . . . . . . . . . .
Clamp Low Pressure Close Profile Setpoints 2–12 . . . . . . . . . .
Critical Process Setpoints 2–12 . . . . . . . . . . . . . . . . . . . . . . . .
DYC – Dynamic Command Block 2–13 . . . . . . . . . . . . . . . . . . . .
Bit-mapped Control Words 2–13 . . . . . . . . . . . . . . . . . . . . . . .
Direct Set-output Values 2–25 . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Set-output Ramp Rates 2–25 . . . . . . . . . . . . . . . . . . . .