Rockwell Automation 1771-QDC PLASTIC MOLD.MODULE - Manual (Page 208)

3–32 Status Word/Bit Descriptions
Publication 1771-6.5.88 – July 1997
Notes: 1. For [ ] engineering units, see page 3.
2. When using the Inject/Clamp/Eject mode, all pressure readings are system pressure at input 2, except where noted.
Word Bit Description
SYS06 B08 = 0 Normal
= 1 Post-decompress Movement High Ram (Screw) Pressure
The module sets this bit when real-time ram (screw) pressure equals or exceeds PSC57.
B09 = 0 Normal
= 1 First Clamp Open Profile High Clamp Pressure
The module sets this bit when real-time clamp pressure equals or exceeds FOC57.
B10 = 0 Normal
= 1 Second Clamp Open Profile High Clamp Pressure
The module sets this bit when real-time clamp pressure equals or exceeds SOC57.
B11 = 0 Normal
= 1 Third Clamp Open Profile High Clamp Pressure
The module sets this bit when real-time clamp pressure equals or exceeds TOC57.
B12 = 0 Normal
= 1 Clamp Open Slow Profile High Clamp Pressure
The module sets this bit when real-time clamp pressure equals or exceeds OSC57.
B13 = 0 Normal
= 1 Ejector Profile High Ejector Pressure
The module sets this bit when real-time ejector pressure equals or exceeds EAC57.
B14 - B15 Open
SYS07 Overtravel Alarm Status (Real Time)
The module sets alarm bits in real time. These bits are not latched.
You can inhibit each bit by setting its associated alarm setpoint to zero.
B00 = 0 Normal
= 1 Ram (Screw) Overtravel at Bottom
The module sets this bit when real-time ram (screw) position is less than or equal to MCC13. The module resets this
bit when real-time position equals or exceeds the position defined by MCC13 + MCC15.
When SET, the module ignores any profile action execution command in DYC02.
B01 = 0 Normal
= 1 Ram (Screw) Overtravel at Top
The module sets this bit when real-time ram (screw) position equals or exceeds MCC14. The module resets this bit
when real-time position is less than or equal to the position defined by MCC14 – MCC15.
When SET, the module ignores any profile action execution command in DYC02.
B02 = 0 Normal
= 1 Clamp Overtravel on Close
The module sets this bit when real-time clamp position is less than or equal to MCC27. The module resets this bit
when real-time clamp position equals or exceeds the position defined by MCC27 + MCC29.
When SET, the module ignores any profile action execution command in DYC02.
B03 = 0 Normal
= 1 Clamp Overtravel on Open
The module sets this bit when real-time clamp position equals or exceeds MCC28. The module resets this bit when
real-time clamp position is less than or equal to the position defined by MCC28 – MCC29.
When SET, the module ignores any profile action execution command in DYC02.
B04 = 0 Normal
= 1 Ejector Overtravel on Retract
The module sets this bit when real-time ejector position is less than or equal to MCC41. The module resets this bit
when real-time ejector position equals or exceeds the position defined by MCC41 + MCC43.
When SET, the module ignores any profile action execution command in DYC02.
B05 = 0 Normal
= 1 Ejector Overtravel on Advance
The module sets this bit when real-time ejector position equals or exceeds MCC42. The module resets this bit when
real-time ejector position is less than or equal to the position defined by MCC42 – MCC43.
When SET, the module ignores any profile action execution command in DYC02
B06 = 0 Normal
= 1 Clamp Close Profile Overtravel into Mold Protection Zone
The module sets this bit during one of the first three Clamp Close Profiles when real-time clamp position is less than or
equal to CPC61. Module resets this bit on next false-to-true transition of an action execution bit in DYC01 or DYC02.