Rockwell Automation 1771-QDC PLASTIC MOLD.MODULE - Manual (Page 121)

2–55 Command Word/Bit Descriptions
Publication 1771-6.5.88 – July 1997
INC
Word Description
INC17 Output #1 Acceleration Ramp Rate during Profile [20]
INC18 Output #2 Acceleration Ramp Rate during Profile [20]
INC19 Output #3 Acceleration Ramp Rate during Profile [20]
INC20 Output #4 Acceleration Ramp Rate during Profile [20]
INC21 Output #5 Acceleration Ramp Rate during Profile [20]
INC22 Output #6 Acceleration Ramp Rate during Profile [20]
INC23 Output #7 Acceleration Ramp Rate during Profile [20]
INC24 Output #8 Acceleration Ramp Rate during Profile [20]
INC25 Output #1 Deceleration Ramp Rate during Profile [20]
INC26 Output #2 Deceleration Ramp Rate during Profile [20]
INC27 Output #3 Deceleration Ramp Rate during Profile [20]
INC28 Output #4 Deceleration Ramp Rate during Profile [20]
INC29 Output #5 Deceleration Ramp Rate during Profile [20]
INC30 Output #6 Deceleration Ramp Rate during Profile [20]
INC31 Output #7 Deceleration Ramp Rate during Profile [20]
INC32 Output #8 Deceleration Ramp Rate during Profile [20]
INC33 - 40 Open
Pressure Control Limits
Word Description
INC41 Pressure Minimum Control Limit [01] Minimum controllable ram (screw) pressure attainable during any Press/Pos or Press/Time
Injection Profile. The module expects this ram (screw) pressure when setting its selected pressure valve to the %-output in INC43.
INC42 Pressure Maximum Control Limit [01] Maximum controllable ram (screw) pressure attainable during any Press/Pos or Press/Time
Injection Profile. The module expects this ram (screw) pressure when setting its selected pressure valve to the %-output in INC44.
INC43 Selected Pressure Valve Output for Minimum [19] 0% CV output percentage that the module uses to drive the selected pressure
valve during any Press/Pos or Press/Time Injection Profile. The module expects a pressure equal to INC41 when setting the se-
lected pressure valve to this %-output during profile execution. The Press/Pos or Press/Time Injection Profile will be executed as a
reverse-acting algorithm if this entry is greater than INC44.
INC44 Selected Pressure Valve Output for Maximum [19] 100% CV output percentage that the module uses to drive the selected pressure
valve during any Press/Pos or Press/Time Injection Profile. The module expects a pressure equal to INC42 when setting the se-
lected pressure valve to this %-output during profile execution. The Press/Pos or Press/Time Injection Profile will be executed as a
reverse-acting algorithm if this entry is less than INC43.
Velocity Control Limits
Word Description
INC45 Velocity Minimum Control Limit [06] Minimum controllable ram (screw) velocity attainable during any Vel/Pos Injection Profile. The
module expects this ram (screw) velocity when setting its selected velocity valve to the %-output in INC47.
INC46 Velocity Maximum Control Limit [06] Maximum controllable ram (screw) velocity attainable during any Vel/Pos Injection Profile. The
module expects this ram (screw) velocity when setting its selected velocity valve to the %-output in INC48.
INC47 Selected Velocity Valve Output for Minimum [19] 0% CV output percentage that the module uses to drive the selected velocity valve
during any Vel/Pos or LimVel/Pos Injection Profile. The module expects a velocity equal to INC45 when setting the selected velocity
valve to this %-output during profile execution. The Vel/Pos or LimVel/Pos Injection Profile will be executed as a reverse-acting
algorithm if this entry is greater than INC48.
INC48 Selected Velocity Valve Output for Maximum [19] 100% CV output percentage that the module uses to drive the selected velocity
valve during any Vel/Pos or LimVel/Pos Injection Profile. The module expects a velocity equal to INC46 when setting the selected
velocity valve to this %-output during profile execution. The Vel/Pos or LimVel/Pos Injection Profile will be executed as a reverse-
acting algorithm if this entry is less than INC47.