Rockwell Automation 8520-GUM 9/Series CNC Grinder Operation and Programming Manual Documentation Set - Manual (Page 806)

9/Series Grinder
Index
Operation and Programming Manual
ii
Changing and Inserting, 5-7
Changing Languages, 8-23
Changing Parameters
Auto Erase, 8-32
Auto Size, 8-30
Grid Lines, 8-30
Overtravel Zone Lines, 8-30
Process Speed, 8-32
Rapid Traverse, 8-29
Select Graph, 8-29
Sequence Starting #:, 8-31
Sequence Stopping #:, 8-31
Changing parameters, {GRAPH SETUP}, 8-28
Chinese, Language Display, 8-23
circular interpolation, on angled wheel grinder, 14-6
Circular Interpolation Mode (G02, G03), 12-5
Clamp, feedrate G16.4 mode, 14-9
clamp, feedrate on angled-wheel grinder, 14-6
Clearing Messages, 2-40
Clearing Screen, 8-33
Clock, system, 2-44
Comment Block, 10-10
Comment Display, 5-40
Communications Port Parameters, 9-3
changing values, 9-1
error conditions, 9-18
port A, port B, 9-3
Computer interface, ODS, 9-4
Configuration Assumptions for Angled-Wheel Grinders, 14-1
Connecting the Workstation to the Control, 6-5
Constant Surface Speed, see CSS, 12-34
Continuous Jogging, 4-3
Control and Block Reset, 2-36
Control Commands, transfer, 20-7
Controlling Spindles, (G12.1, G12.2, G12.3), 12-71
Coordinate System
machine, 11-2
offsets, 11-13
rotate, 11-23
rotating (G68, G69), 11-24
rotating external, 11-28
work, 11-4
Coordinate System Label, entering, 3-22
Copying Programs, 5-41
Corner Radius, 12-22
Corner Rounding, 12-69
eliminating, 12-69
Crossover, 16-6, 16-9
CRT, 2-7
CRT Displays, 8-1
CRT screen saver, 8-39
CSS, 12-34
axis selection, 12-45
during surface grinding, 12-36
notes, 12-42
spindle speed, limiting with G92, 12-43
CSS on an Angled-wheel grinder, 14-5
Current Dresser RPM, 21-9
Current Wheel Diameter, 21-9
Cursor
changing size, 5-6
moving, 5-5
Custom Screens, through PAL, 8-22
Cycle Start, 2-10
Cycle Stop, 2-10
Cycles
cancel, 16-8, 17-8
considerations, 16-2, 17-3
continuous G85 (surf. grind.), 16-20
continuous G86 (surf. grind.), 16-23
incremental face G82 (cyl. grind.), 17-12
incremental G83 (surf. grind), 16-16
incremental G84 (surf. grind.), 16-19
incremental plunge G83 (cyl. grind), 17-16
multi-step plunge G89 (cyl.grind.), 17-32
multi pass diameter G85 (cyl. grind.), 17-23
multi pass face G84 (cyl. grind.), 17-20
plunge (surf. grind.), 16-14
reciprocation, 16-4, 17-5
reciprocation (cyl. grind.), 17-11
reciprocation (surf. grind.), 16-13
shoulder G86 (cyl. grind.), 17-26
shoulder G87 (cyl. grind.), 17-28, 17-32
shoulder G88 (cyl. grind.), 17-30
cycles, on angled wheel grinder, 14-6
Cylindrical Grinding, 17-1
considerations, 17-3
using CSS, 12-37, 12-40