Lenze EVF9333−xV - Manual (Page 505)

Appendix
Index
13
13.2
l
13.2−7 EDSVF9333V EN 6.2−04/2012
Safety relay KSR, Terminal assignment, 5.8−8 , 11.3−2
Selecting the operating mode, speed mode, setting
acceleration and deceleration times, 6.10−3
Selection, operating mode, 6.1−1 , 6.8−1
Selection of motor type, 6.6−1 , 8.2−29 , 8.2−52 , 8.5−9
Selection of the feedback system, 6.7−1 , 8.2−50 , 8.5−4
Setting integral action component, 8.2−60
Setting the acceleration time, 6.10−3
Setting the deceleration time, 6.10−3
Setting the feedback system, 6.7−1
Setting the speed feedback, 6.7−1
Site altitude, 3.1−2
Slip compensation, 6.11−1 , 8.2−47 , 8.2−76
Speed control, 8.2−34 , 8.2−59
− adapting the speed controller, 8.2−59
− at vector control (MCTRL2), adapting the speed
controller, 8.2−34
− with vector control (MCTRL2)
setting integral action component, 8.2−60
speed feedback, 8.2−59
temperature detection, 8.2−60
Speed feedback, 8.2−59
Speed mode, setting acceleration and deceleration times,
6.10−3
Speed oscillations, 6.11−3
Speed setpoint limitation, 8.2−33 , 8.2−58
Speed setpoint selection, 8.2−33 , 8.2−58
Stability, of the motor, 8.2−61
Status display, keypad XT EMZ9371BC, 7.2−2
Status word AIF, 8.5−16 , 9.1−2
Stopping, 6.10−1
Supply conditions, 5.4−5 , 5.4−7 , 5.5−5 , 5.5−6 , 5.6−5 ,
5.6−6 , 5.7−5 , 5.7−6 , 10.3−1
Supply forms, IT system, 5.2−2
Supply forms / electrical supply conditions, 5.2−1
Switch−on, check before switching on, 6.1−1
Switching frequency, automatic current−depending
change−over, 6.9−2 , 8.2−27 , 8.2−49 , 8.5−4
Switching frequency of inverter, 6.9−1
− noise optimised, 6.9−1
Switching frequency reduction, 6.9−2
System bus (CAN), wiring, 5.9−1
System error messages, 9.5−1
− configuration, 8.41
− General, 9.5−1
− Resetting, 9.5−5
T
Table of attributes, 8.7−1
Technical data, 3−1
− current characteristic, device protection by current
derating, 3.6−1
− General data, 3.1−1
− Operating conditions, 3.1−1
− Operation with rated power, Rated data 480 V, 3.4−3
technical data, Operation with rated power, 3.4−1
Technicaldata, Operation with increased rated power,
3.5−1
Temperature detection, 8.2−60
Terminal assignment
− analog inputs, 5.8−8
− analog outputs, 5.8−8
− digital inputs, 5.8−8
− Digital inputs/outputs, 11.3−2
− digital outputs, 5.8−8
− Safety relay KSR, 5.8−8 , 11.3−2
Terminal data, 5.8−2 , 11.3−1
Terms
− controller, 13.1−1
− Definitions, 13.1−1
− drive, 13.1−1
Thermal monitoring, motor
− Sensorless, 2.2−1
− with PTC thermistor, 6.6−8 , 6.6−10
T
n
current controller, 6.8−8 , 8.2−29 , 8.2−51 , 8.5−8
T
n
slip controller, 6.11−1 , 8.2−29 , 8.5−8
T
n
speed controller, 8.2−28 , 8.2−51 , 8.5−8
Torque control with speed limitation, in case of vector
control (MCTRL2), 8.2−64
Torque limitation in the field weakening range, with
vector control (MCTRL2), 8.2−61
TRIP, 8.3−1
Troubleshhoting and fault elimination, monitoring,
DC−bus voltage, 8.3−8