Rockwell Automation 1761-HHP-B30 MicroLogix 1000 with Hand-Held Programmer (HHP) - Manual (Page 13)

(HHP) User Manual
Table of Contents
MicroLogix
t 1000 with Hand–Held Programmer
toc–v
Selectable Timed Disable (STD) and Enable (STE) 13–17 . . . . . . . . . . . . . . . . . . .
Selectable Timed Start (STS) 13–18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Subroutine (INT) 13–19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Specific Instructions in the Paper Drilling Machine
Application Example 13–20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 14
About the High-Speed Counter Instructions 14–1 . . . . . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter Instructions Overview 14–2 . . . . . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter (HSC) 14–4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter Load (HSL) 14–15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter Reset (RES) 14–19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter Reset Accumulator (RAC) 14–20 . . . . . . . . . . . . . . . . . . . . . .
High-Speed Counter Interrupt Enable (HSE) and Disable (HSD) 14–21 . . . . . . . . . .
Update High-Speed Counter Image Accumulator (OUT) 14–23 . . . . . . . . . . . . . . . .
What Happens to the HSC When Going to RRUN Mode 14–23 . . . . . . . . . . . . . . . .
High-Speed Counter Instructions in the Paper Drilling Machine
Application Example 14–28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 15
Types of Communication 15–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message Instruction (MSG) 15–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Diagram for a Successful MSG Instruction 15–9 . . . . . . . . . . . . . . . . . . . .
MSG Instruction Error Codes 15–11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Examples that Use the MSG Instruction 15–12 . . . . . . . . . . . . . . . . . . .
Chapter 16
Programming Examples 16–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming Considerations 16–8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 17
Entering the Program Monitor 17–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing Considerations 17–3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing Modes 17–3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting Instructions and Rungs 17–6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Searching for Specific Addresses 17–8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using High–Speed Counter
Instructions
Using Communication
Protocols
Instruction List Programming
Concepts
Entering and Editing Your
Program