Rockwell Automation FlexPak 3000 Digital DC Drive Version 4.3 - Manual (Page 189)

Index Index-3
frequency
input
block diagram, 11-10
setting parameters, 11-10
output, setting parameters, 11-11
I
I/O expansion board parameters, 11-1
I / O EXPANSION KIT (P.797), 11-1
INERTIA COMP SELECT (P.221), 6-2
INV FAULT AVOID SEL (P.312), 13-20
inverting fault avoidance, 13-20, 13-21
IR COMPENSATION (P.206), 5-5
IR COMPENSATION TP (P.290), 5-5
J
J11 ANLG TACH VLT SCL (P.792), 5-8
J14 ANLG TACH VLT RNG (P.793), 5-8
J15 REGULATOR TYPE (P.799), 13-23
J18 ARM I FB RESISTOR (P.395), 6-7
J20 FIELD LOSS DETECT (P.597), 8-4
J21 FLD SUPPLY JUMPER (P.598), 8-5
jog
mode, 2-2
sequencing, 2-2
JOG ACCEL / DECEL TIME (P.013), 4-26
JOG OFF DELAY TIME (P.121), 4-27
JOG RAMP OUTPUT (P.294), 4-27
JOG SPEED 1 (P.012), 4-27
JOG SPEED 2 (P.017), 4-27
jumpers
settings
table of adjustment settings, C-15
K
keypad speed reference, 4-23
L
LEVEL DETECT 1 DELAY (P.604), 12-1
LEVEL DETECT 1 OUTPUT (P.648), 12-2
LEVEL DETECT 1 SELECT (P.602), 12-2
LEVEL DETECT 1 THRESH (P.603), 12-2
LEVEL DETECT 2 DELAY (P.607), 12-3
LEVEL DETECT 2 OUTPUT (P.649), 12-3
LEVEL DETECT 2 SELECT (P.605), 12-3
LEVEL DETECT 2 THRESH (P.606), 12-4
level detectors
block diagram, 12-1
set up, 12-1
M
manual mode, 4-2
MANUAL REF SELECT (P.106), 4-7
MAXIMUM CURRENT (P.007), 6-2
MAXIMUM SPEED (P.004), 4-20
METER OUT 1 GAIN ADJ (P.400), 7-2
METER OUT 1 SELECT (P.404), 7-2
METER OUT 1 ZERO ADJ (P.402), 7-2
METER OUT 2 GAIN ADJ (P.401), 7-3
METER OUT 2 SELECT (P.405), 7-3
METER OUT 2 ZERO ADJ ( P .403), 7-3
metering
outputs, 7-1
block diagram, 7-1
parameter options, 7-4, 11-12
MINIMUM SPEED (P.003), 4-20
mode
auto, 4-2
jog, 2-2
manual, 4-2
run, 2-2
mop
block diagram, 4-9
manual reference to speed/voltage loop, 4-8
MOP ACCEL TIME (P.115), 4-10
MOP DECEL TIME (P.120), 4-10
MOP OUTPUT (P.191), 4-10
MOP RESET ENABLE (P.116), 4-10
MOTOR HOT FLD AMPS (P.510), 8-8
MOTOR RATED ARM AMPS (P.008), 6-8
MOTOR RATED ARM VOLTS (P.009), 5-5
motor-operated potentiometer See MOP
N
NEG CUR LIM INV EN (P.226), 5-15, 6-4
NEG CURRENT LIM SEL (P.224), 5-15
NEGATIVE CURRENT LIM (P.006), 5-16
NETW COMM LOSS SELECT (P.901), 10-2
NETW COMM STATUS (P.908), 10-3
NETW CONNECT TYPE (P.910), 10-3
NETW DROP NUMBER (P.900), 10-4
NETW IN REG 1 (P.905), 10-5
NETW IN REG 2 (P.906), 10-5
NETW IN REG 3 (P.907), 10-5
NETW OUT REG 1 SELECT (P.902), 10-4
NETW OUT REG 2 SELECT (P.903), 10-4