Yaskawa AC Drive P1000 Bypass Technical Manual User Manual
Page 384
Hybrid IC Failure ............................................................... 177
I
I/O Connections...................................................................51
IGBT Maintenance ............................................................. 265
IGBT Maintenance Time (50%) .............................................. 193
IGBT Maintenance Time (90%) ............................................. 195
Initialization .......................................................................82
Input Current ........................................................ 224, 225, 226
Input Phase Detection Level .................................................. 252
Input Phase Loss ................................................................ 187
Input Phase Loss Detection Level ............................................ 137
Input Phase Loss Protection Selection ................................. 136, 252
Input Terminal Status .......................................................... 261
Input Terminal Status at Previous Fault ..................................... 262
Input Voltage Setting........................................................... 109
Inrush Prevention Circuit Fault ............................................... 189
Inspection .................................................................. 214, 215
Installation Area ..................................................................38
Installation Environment.........................................................38
Integral Limit Setting.............................................................94
Integral Time Setting (I) .........................................................94
Interlock Open .................................................................. 193
inTLK ............................................................................ 193
J
Jumper S1..........................................................................33
Jumper S1 Settings ...............................................................52
Jump Frequency................................................................. 172
Jump Frequency Width ........................................................ 108
K
Keys and Displays on the HOA Keypad.......................................59
kWh............................................................................... 265
kWh, Lower 4 Digits ........................................................... 265
kWh, Upper 5 Digits ........................................................... 265
L
L3-01 through L3-06 ........................................................... 172
L3-02 ....................................................................... 207, 209
L3-04 ............................................................................. 208
L3-06 ............................................................................. 207
L3-11 ............................................................................. 172
LCD Display ......................................................................60
LED Check ...................................................................... 265
LF ................................................................................. 183
LF2 ............................................................................... 183
Line-to-Line Resistance Error................................................. 201
Load Inertia Ratio......................................................... 131, 251
Loopback Test................................................................... 316
Loss of Load..................................................................... 190
Loss of Reference Function ................................................... 131
Low Voltage Directive ......................................................... 336
LT-1 .............................................................................. 193
LT-2 .............................................................................. 193
LT-3 .............................................................................. 193
LT-4 .............................................................................. 193
M
Main Circuit Terminal ...........................................................33
Main Circuit Terminal and Motor Wiring.....................................43
Main Circuit Wiring ..............................................................43
Main Input Circuit Wiring.......................................................33
Maintenance ..................................................................... 217
Maintenance Alarms ........................................................... 218
Maintenance Monitors ......................................................... 150
Maintenance Monitor Settings ................................................ 142
Master Speed Reference Lower Limit ....................................... 107
Maximum Applicable Motor Capacity .......................... 224, 225, 226
Maximum Output Frequency...................................... 224, 225, 226
Maximum Output Voltage......................................... 224, 225, 226
Maximum Voltage.............................................................. 112
MEMOBUS/Modbus Comm. Test Mode Complete ....................... 195
MEMOBUS/Modbus Communication Error.......................... 176, 191
MEMOBUS/Modbus Communications Reference......................... 266
MEMOBUS/Modbus Data Table............................................. 318
MEMOBUS/Modbus Error Codes ........................................... 332
MEMOBUS/Modbus Setup Parameters ..................................... 310
MEMOBUS/Modbus Specifications ......................................... 307
Message Format................................................................. 314
Metasys N2 Point Database ................................................... 366
Minimum Wait Time for Sending Messages.......................... 313, 365
Minor Alarms ................................................................... 174
Minor Fault ...................................................................... 200
Minor Fault and Alarm Displays ............................................. 175
Minor Faults ..................................................................... 174
Minor Faults and Alarms ................................................ 173, 174
Model Number and Nameplate Check .........................................28
Modes ..............................................................................66
Modified Constants...............................................................67
Momentary Overcurrent Protection .......................................... 227
Momentary Power Loss Minimum Baseblock Time................. 128, 250
Momentary Power Loss Operation Selection ...........................88, 250
Momentary Power Loss Ride-Thru .................................... 127, 228
Momentary Power Loss Ride-Thru Time ............................. 128, 250
Monitor Parameters....................................................... 123, 259
Most Recent Fault .............................................................. 263
Motor 1 Parameters............................................................. 113
Motor Base Frequency ................................................ 78, 80, 257
Motor Base Speed ..........................................................80, 258
Motor Data Error................................................................ 200
Motor Does Not Rotate ........................................................ 205
Motor Hunting and Oscillation Control Parameters ....................... 172
Motor Iron Loss .............................................................80, 258
Motor is Too Hot ............................................................... 206
Motor No-Load Current........................................................ 113
Motor Overheat ................................................................. 194
Motor Overheat Alarm (PTC Input).......................................... 185
Motor Overheat Fault (PTC Input) ........................................... 185
Motor Overload ................................................................. 185
Motor Overload Estimate (oL1) .............................................. 265
Motor Overload Protection Selection .................................. 126, 250
Motor Overload Protection Time ....................................... 127, 250
Motor Performance Fine-Tuning ............................................. 172
Motor Poles........................................................................78
Motor Protection ................................................................ 126
Motor Pull Out or Step Out Detection ....................................... 188
Motor q-Axis Current at Previous Fault ..................................... 262
Motor Rated Current ............................................ 78, 80, 113, 257
Motor Rated Power .........................................................79, 257
Motor Rated Voltage .................................................. 78, 79, 257
Index
384
YASKAWA SIEP YAIP1B 01A YASKAWA AC Drive – P1000 Bypass Technical Manual