Yaskawa AC Drive P1000 Bypass Technical Manual User Manual
Page 386
Performance Life ............................................................... 217
Performance Life Monitors Maintenance Monitors........................ 217
Periodic Inspection ............................................................. 215
Periodic Maintenance .......................................................... 217
PF ................................................................................. 187
PID Accel/Decel Time ...........................................................98
PID Block Diagram...............................................................93
PID Control........................................................................90
PID Feedback 1 ................................................................. 266
PID Feedback High Detection Level...........................................97
PID Feedback High Detection Time ...........................................97
PID Feedback Input Methods ...................................................92
PID Feedback Loss Detection Selection.......................................96
PID Feedback Low Detection Level ...........................................96
PID Feedback Low Detection Time............................................96
PID Fine Tuning ................................................................ 101
PID Input (feedback) ........................................................... 266
PID Input Limit ...................................................................99
PID Monitors .................................................................... 150
PID Offset Adjustment...........................................................94
PID Output....................................................................... 266
PID Output Gain Setting.........................................................95
PID Output Level Selection .....................................................95
PID Output Limit .................................................................94
PID Output Lower Limit.........................................................99
PID Output Reverse Selection ..................................................95
PID Output Reverse Selection 2 .............................................. 100
PID Primary Delay Time Constant .............................................94
PID Setpoint ..................................................................... 266
PID Setpoint Display Digits.....................................................99
PID Setpoint Input Methods.....................................................91
PID Setpoint Monitor Unit Selection ........................................ 100
PID Setpoint Scaling .............................................................98
PID Setpoint Selection ...........................................................98
PID Setpoint User Display ......................................................99
PID Setpoint Value ...............................................................98
PID Sleep ..........................................................................97
PID Sleep Delay Time ...........................................................98
PID Sleep Function Start Level .................................................97
PI Feedback Loss ......................................................... 182, 192
Powering Up the Drive...........................................................70
Power Ratings ................................................................... 224
Predefined V/f Patterns ........................................................ 109
Preface..............................................................................14
Preparing the Ends of Shielded Cables ........................................51
Present Value Access........................................................... 295
Preset Reference Timing Diagram ........................................... 106
Previous Fault ............................................................. 260, 262
Previous Fault Hour Minute................................................... 260
Previous Fault Month Day..................................................... 260
Previous Fault Year............................................................. 260
Programmable Run Timers for Real Time Clock (RTC).................. 144
Programming Errors............................................................ 197
Programming Mode ..............................................................66
Proportional Gain Setting (P) ...................................................94
Protective cover to prevent miswiring .........................................33
Q
R
R/L1 ................................................................................43
Ramp to stop ......................................................................83
Rated Current Setting Alarm .................................................. 200
Rated Output Current............................................... 224, 225, 226
Rated Slip Error ................................................................. 201
Rated Voltage, Rated Frequency ................................. 224, 225, 226
Reading BACnet Bypass Parameters ........................................ 301
Reading Drive MEMOBUS/Modbus Register Contents .................. 316
Real Time Clock ................................................................ 144
Replacement Parts .............................................................. 217
RESET Key........................................................................59
Resistance Tuning Error ....................................................... 200
Response Messages from Drive to Master ............................ 313, 365
Reverse Operation Selection ....................................................84
Rotational Auto-Tuning for V/f Control.......................................76
Run Command/Frequency Reference Source Selection Error............ 198
Run Command Selection ...................................................... 205
Run Command Source Selection ............................................. 265
S
S: Special Parameters .................................................... 143, 255
S/L2.................................................................................43
S1: Dynamic Noise Control Function........................................ 255
S2: Sequence Timers ..................................................... 144, 255
SAFE ............................................................................. 195
Safety Standard ................................................................. 228
S-Curve Characteristics .................................................. 103, 172
SE ................................................................................. 195
Selecting the Type of Auto-Tuning ............................................77
Sequence Timer 1............................................................... 144
Sequence Timer 1 Day Selection ............................................. 255
Sequence Timer 1 Reference Source......................................... 255
Sequence Timer 1 Selection................................................... 255
Sequence Timer 1 Start Time ................................................. 255
Sequence Timer 1 Stop Time ................................................. 255
Sequence Timer 2 Day Selection ............................................. 256
Sequence Timer 2 Reference Source......................................... 256
Sequence Timer 2 Selection................................................... 256
Sequence Timer 2 Start Time ................................................. 256
Sequence Timer 2 Stop Time ................................................. 256
Sequence Timer 3 Day Selection ............................................. 256
Sequence Timer 3 Reference Source......................................... 256
Sequence Timer 3 Selection................................................... 256
Sequence Timer 3 Start Time ................................................. 256
Sequence Timer 3 Stop Time ................................................. 256
Sequence Timer 4 Day Selection ............................................. 257
Sequence Timer 4 Reference Source......................................... 257
Sequence Timer 4 Selection................................................... 257
Sequence Timer 4 Start Time ................................................. 256
Sequence Timer 4 Stop Time ................................................. 257
Sequence Timer Error .......................................................... 199
Sequence Timers 1/2/3/4 Reference Source................................. 146
Sequence Timers 1/2/3/4 Selection........................................... 145
Sequence Timers 1 to 4 Day Selection....................................... 145
Sequence Timers 1 to 4 Start Time........................................... 145
Sequence Timers 1 to 4 Stop Time ........................................... 145
Sequence Timers 2 to 4 ........................................................ 145
SEr ................................................................................ 188
Serial Comm Fault.............................................................. 190
Index
386
YASKAWA SIEP YAIP1B 01A YASKAWA AC Drive – P1000 Bypass Technical Manual