MITSUBISHI ELECTRIC Mitsubishi Programmable Logic Controller QD75D User Manual
Page 752
Index - 2
AFTER mode............................................... 12-63
AFTER mode (Explanation of positioning terms)
.......................................................... Appendix-69
Allowable circular interpolation error width
(
Pr.41
)........................................................ 5-43
Applicable system ........................................... 2-5
Applicable wire size......................................... 3-2
Arc address ( Da.7 )..................................... 5-68
Auto tuning (Explanation of positioning terms)
.......................................................... Appendix-70
Automatic trapezoidal acceleration/deceleration
(Explanation of positioning terms) ... Appendix-70
Automatic trapezoidal acceleration/deceleration
processing method...................................... 12-81
Axis display LED ............................................. 4-3
Axis error No. (
Md.10
,
Md.23
)............... 5-92,96
Axis error occurrence (Hour) (
Md.11
)........ 5-92
Axis error occurrence (Minute: second) (
Md.12
)
....................................................................... 5-92
Axis error reset ( Cd.5 ) ............................. 5-112
Axis feedrate (
Md.28
)............................... 5-100
Axis in which the error occurred (
Md.9
) .... 5-92
Axis in which the warning occurred (
Md.14
)
....................................................................... 5-94
Axis monitor data........................................... 5-96
Axis operation status (
Md.26
) .................... 5-98
Axis stop signal.............................................. 3-21
Axis to be interpolated (
Da.5
) .................... 5-62
Axis warning detection ................................ 5-102
Axis warning No. (
Md.15
,
Md.24
) ........ 5-94,98
Axis warning occurrence (Hour) (
Md.16
)... 5-94
Axis warning occurrence (Minute: second)
(
Md.17
)........................................................ 5-94
[B]
Backlash compensation amount (
Pr.11
). 5-28
Backlash compensation (Explanation of
positioning terms) ............................. Appendix-70
Backlash compensation function ................ 12-11
Backup function (Explanation of positioning terms)
.......................................................... Appendix-70
Ball screw (Explanation of positioning terms)
.......................................................... Appendix-70
Basic parameters 1........................................5-20
Basic parameters 2........................................5-26
BCD (Explanation of positioning terms)
.......................................................... Appendix-71
Bias speed at start ( Pr.7 ) ..........................5-26
Bias speed at start (Explanation of positioning
terms) ............................................... Appendix-71
BIN (Explanation of positioning terms)
.......................................................... Appendix-71
Bipolar drive constant-current system (Explanation
of positioning terms) ........................ Appendix-72
Block...............................................................10-2
Block No. being executed (
Md.45
) ...........5-108
Block start (Normal start) ...............................10-2
Block start data ..............................................10-7
Block start data area (Nos. 7000 to 7004) ......7-3
Buffer memory..................................................7-2
Buffer memory (Explanation of positioning terms)
.......................................................... Appendix-72
Buffer memory area configuration...................7-5
BUSY (Explanation of positioning terms)
.......................................................... Appendix-72
BUSY signal ...................................................3-14
[C]
Cable clamp .....................................................4-9
CCW (Explanation of positioning terms)
.......................................................... Appendix-72
CHANGE signal (Explanation of positioning terms)
.......................................................... Appendix-72
Circular interpolation (Explanation of positioning
terms) ............................................... Appendix-72
Combination of functions ...............................3-12
Combination of main functions and sub functions
........................................................................3-12
Command in-position flag............................5-102
Command in-position function.....................12-77
Command in-position width (
Pr.16
) ..........5-30
Command pulse (Explanation of positioning terms)
.......................................................... Appendix-72
Command pulse frequency ...........................1-11
Command speed ( Da.8 ).............................5-70
Common functions................................. 3-8, 13-2