Toshiba H9 - Manual (Page 249)

H9 ASD Installation and Operation Manual 241
Table 8. Terminal assignments and the associated My Function Input Setting (Input Function Target) and Parameter Setting
numbers for the FLA/B/C, O1A/O1B (OUT1), O2A/O2B (OUT2), OUT3–OUT6, R1–R4 terminals.
Discrete Output Terminal Assignment Selections
Input
Setting
Param
Setting
Function
Input
Setting
Param
Setting
Function
1000 0 Lower Limit Frequency 1086 86 Error Code Output 4
1002 2 Upper Limit Frequency 1088 88 Error Code Output 5
1004 4 Low Speed Signal 1090 90 Error Code Output 6
1006 6 Acceleration/Deceleration Completion 1092 92 Specified Data Output 1
1008 8 Speed Reach Signal 1094 94 Specified Data Output 2
1010 10 Failure FL (All trips) 1096 96 Specified Data Output 3
1012 12 Failure FL (Except EF, OCL, EPHO, OL2) 1098 98 Specified Data Output 4
1014 14 Overcurrent (OC) Alarm 1100 100 Specified Data Output 5
1016 16 ASD Overload (OL1) Alarm 1102 102 Specified Data Output 6
1018 18 Motor Overload (OL2) Alarm 1104 104 Specified Data Output 7
1020 20 Overheat Alarm 1106 106 Light Load
1022 22 Overvoltage Alarm 1108 108 Heavy Load
1024 24 Main Circuit (MOFF) Undervoltage Alarm 1110 110 Positive Torque Limit
1026 26 Low Current Alarm 1112 112 Negative Torque Limit
1028 28 Overtorque Alarm 1114 114 External Rush Suppression Relay Activated
1030 30 DBR Overload Alarm 1118 118 Completion of Stop Positioning
1032 32 Emergency Off Active 1120 120 L-STOP
1034 34 Retry Active 1122 122 Power Failure Synchronized Operation
1036 36 Pattern Operation Switching Output 1124 124 Traverse in Progress
1038 38 PID Deviation Limit 1126 126 Traverse Deceleration Active
1040 40 Run/Stop 1128 128 Part Replacement Alarm
1042 42 Serious Failure (OCA, OCL, EF, phase failure, etc.) 1130 130 Overtorque Alarm
1044 44 Light failure (OL, OC1, 2, 3, OP) 1132 132 Frequency Command ½ Selection
1046 46 Commercial Power/ASD Switching Output 1 1134 134 Failure FL (Except Emergency Off)
1048 48 Commercial power/ASD switching Output 2 1222 222 My Function Output 1
1050 50 Cooling Fan ON/OFF 1224 224 My Function Output 2
1052 52 Jogging Operation Active (jog run active) 1226 226 My Function Output 3
1054 54 Panel/Terminal Board Operation Switching 1228 228 My Function Output 4
1056 56 Cumulative Run-time Alarm 1230 230 My Function Output 5
1058 58 ProfiBus/DeviceNet/CC-Link Communication Error 1232 232 My Function Output 6
1060 60 Forward/Reverse Switching 1234 234 My Function Output 7
1062 62 Ready for Operation 1 1236 236 My Function Output 8
1064 64 Ready for Operation 2 1238 238 My Function Output 9
1068 68 Brake Release (BR) 1240 240 My Function Output 10
1070 70 Alarm Status Active 1242 242 My Function Output 11
1072 72 Forward Speed Limit (torque control) 1244 244 My Function Output 12
1074 74 Reverse Speed Limit (torque control) 1246 246 My Function Output 13
1076 76 ASD Healthy Output 1248 248 My Function Output 14
1078 78 RS485 Communication Error 1250 250 My Function Output 15
1080 80 Error Code Output 1 1252 252 My Function Output 16
1082 82 Error Code Output 2 1254 254 Always OFF
1084 84 Error Code Output 3
Note: Only positive logic is available for the listed parameters.