Toshiba H9 User Manual
Page 31
H9 ASD Installation and Operation Manual
23
RX
— The default function assigned to this terminal is the Torque Command setting. The RX terminal
accepts a ±10 VDC input signal that is used to carry out the function assigned to this terminal. This
input terminal may be programmed to raise or lower the speed or torque of the motor via an amplitude
setting or this terminal may be used to regulate the speed or torque of a motor by setting a limit. The
gain and bias of this terminal may be adjusted for application-specific suitability (see
–
). See
for an electrical depiction of the RX terminal. This terminal references CCA.
V/I
(I) — The function of the I input is to receive a 0 – 20 mA input signal that controls a 0 – 80 Hz
output. This is an isolated input terminal. This terminal is identified as V/I on the terminal board and
may be programmed to control the speed or torque of the motor. This terminal cannot be used when
using the V input function. SW301 must be set to I to receive a current input signal at this terminal and
is the default setting from the factory (see
). This terminal references IICC. Scaling
of the V/I terminal is accomplished via
. The gain and bias of this terminal may be adjusted
for application-specific suitability (see
and
).
V/I
(V) — The function of the V input terminal is to receive a 0 – 10 VDC input signal that controls a
0 – 80 Hz output. This is an isolated input terminal. This terminal is identified as V/I on the terminal
board and may be programmed to control the speed or torque of the motor. This terminal cannot be used
when using the I input. SW301 must be set to V to receive a voltage input signal at this terminal (see
). This terminal references IICC. Scaling of the V/I terminal is accomplished via
–
. The gain and bias of this terminal may be adjusted for application-specific suitability
(
and
SU+
— Externally supplied +24 VDC ± 10% @ 1.1 A (minimum) backup control power. This terminal
references CC.
P24
— +24 VDC @ 200 mA power supply for customer use. This terminal references CCA.
PP
— The function of output PP is to provide a 10 VDC/10 mADC output that may be divided using a
potentiometer. The tapped voltage is applied to the RR input to provide manual control of the RR
programmed function. This terminal references CCA.
O1A/B
(OUT1A/B) — The default function assigned to this terminal is Output Low Speed. This
output may be programmed to provide an indication (open or closed) that any 1 of the functions that are
listed in
has taken place. This function may be used to signal external equipment or
). The OUT1 terminal is rated at 2 A/120 VAC and 2 A/30 VDC.
O2A/B
(OUT2A/B) — The default function assigned to this terminal is ACC/DEC Complete. This
output may be programmed to provide an indication (open or closed) that any 1 of the functions that are
listed in
has taken place. This function may be used to signal external equipment or
). The OUT2 terminal is rated at 2A/120 VAC and 2A/30 VDC.
FP
— The default function of this output terminal is to output a series of pulses at a rate that is a
function of the output frequency of the ASD. As the output frequency of the ASD goes up so does the
FP output pulse rate. This terminal may be programmed to provide an output pulse rate that is
proportional to any one of the items listed in
. For further information on this terminal
.
AM
— This output terminal produces an output current that is proportional to the magnitude of the
function assigned to this terminal. The available assignments for this output terminal are listed in
. For further information on this terminal see
.
FM
— This output terminal produces an output current or voltage that is proportional to the magnitude
of the function assigned to this terminal. The available assignments for this output terminal are listed in
. For further information on this terminal see
. The Voltage/Current
output selection is performed at
SU+
P24
PP