Table 6-6. mdrefr register bitmap (sheet 1 of 3) – Intel PXA26X User Manual
Page 205
Intel® PXA26x Processor Family Developer’s Manual
6-15
Memory Controller
Refer to
Table 6-6. MDREFR Register Bitmap (Sheet 1 of 3)
4800 0004
MDREFR
processor
Bit
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
R
eser
ved
K2
F
R
EE
K1
F
R
EE
K0
F
R
EE
SLFR
SH
R
eser
ved
AP
D
K2
D
B
2
K2
RU
N
K1
D
B
2
K1
RU
N
E1
P
IN
K0
D
B
2
K0
RU
N
E0
P
IN
DRI
Reset
0
0
0
0
0
0
1
1
1
1
0
0
1
0
1
0
0
1
*
*
1
1
1
1
1
1
1
1
1
1
1
1
Bits
Name
Description
31:26
—
Reserved
25
K2FREE
SDRAM FREE-RUNNING CONTROL:
0 – SDCLK2 is not free-running
1 – SDCLK2 is free-running (ignores MDREFR[APD] or MDREFR[K2RUN] bits)
Provides synchronous memory with SDCLK2 following a reset in order to reset internal
circuitry.
24
K1FREE
SDRAM FREE-RUNNING CONTROL:
0 – SDCLK1 is not free-running
1 – SDCLK1 is free-running (ignores MDREFR[APD] or MDREFR[K1RUN] bits)
Provides synchronous memory with SDCLK1 following a reset to reset internal circuitry.
23
K0FREE
SDRAM FREE-RUNNING CONTROL:
0 – SDCLK0 is not free-running
1 – SDCLK0 is free-running (ignores MDREFR[APD] or MDREFR[K0RUN] bits)
Provides synchronous memory with SDCLK0 following a reset to reset internal circuitry.
22
SLFRSH
SDRAM SELF-REFRESH CONTROL/STATUS:
Control/status bit for entering and exiting SDRAM self-refresh and is automatically set on a
hardware or sleep reset.
0 – Self refresh disabled
1 – Self refresh enabled
SLFRSH can be set by software to force a self-refresh command. E1PIN does not have to
be cleared. The appropriate clock run bits (K1RUN or K2RUN) must remain set until
SDRAM has entered self-refresh and must be set prior to exiting self-refresh (clearing
SLFRSH). This capability must be used with extreme caution because the resulting state
prohibits automatic transitions for any commands.
Clearing SLFRSH is a part of the hardware or sleep reset procedure for SDRAM.
21
—
Reserved
20
APD
SDRAM/SYNCHRONOUS STATIC MEMORY AUTO-POWER-DOWN ENABLE:
If APD=1 and KxFREE bits are clear, the clock enables and clock pins are automatically
deasserted when none of the corresponding partitions are being accessed.
If APD=1 and KxFREE bits are set, the clock enables only are automatically deasserted
when none of the corresponding partitions are being accessed.
If no SDRAM partitions are being accessed, the SDRAM chips are put into Power-Down
mode and the clocks and clock-enable pins are turned off.
If one SDRAM partition is being used and the other is not, the clock to the partition that is
not being used is turned off.
If no Synchronous Static Memory partitions are being used, the clock and clock enable to
these partitions are turned off and the memory chips are put into Power-Down mode.