Lenze E84DSxxx - Manual (Page 353)

Lenze · 8400 protec StateLine · Reference manual · DMS 4.2 EN · 03/2013 · TD05
353
9 Diagnostics & error management
9.10 Error messages of the operating system
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
9.10.5 Short overview (A-Z)
The table below contains all error messages of the controller operating system in alphabetical order.

Tip!
If you click the cross-reference in the first column, "Error number", you will reach the
detailed description of the respective error message in the following chapter " Cause &
possible remedies ". ( 355)

Note!
For the sake of legibility, the Logbook and C00165 display the error number with the
following syntax:
[Error type].[Error subject area no.].[Error ID]
In this documentation, "xx", a wildcard, stands for the error type since it is configurable
for many error messages.
Error number Error message Response
(Lenze setting)
can be set in CAN Emergency
Error Code
32 bits 16 bits
hex
16 bits
dec
 xx.0125.00001 0x1901 6401 An01: AIN1_I < 4 mA TroubleQuickStop C00598/1 0xF000
 xx.0131.00006 0x1f06 7942 CA06: CAN CRC error No Reaction C00592/1 0x8000
 xx.0131.00007 0x1f07 7943 CA07: CAN bus warn No Reaction C00592/3 0x8000
 xx.0131.00008 0x1f08 7944 CA08: CAN Bus Stopped No Reaction C00592/4 0x8000
 xx.0131.00011 0x1f0b 7947 CA0b: CAN HeartBeatEvent No Reaction C00592/5 0x8130
 xx.0131.00015 0x1f0f 7951 CA0F: CAN control word Fault C00594/2 0xF000
 xx.0127.00002 0x1b02 6914 CE04: MCI communication error No Reaction C01501/1 0x7000
 xx.0127.00015 0x1b0f 6927 CE0F: MCI control word Fault C00594/2 0xF000
 xx.0135.00001 0x2301 8961 CE1: CAN RPDO1 No Reaction C00593/1 0x8100
 xx.0135.00002 0x2302 8962 CE2: CAN RPDO2 No Reaction C00593/2 0x8100
 xx.0135.00003 0x2303 8963 CE3: CAN RPDO3 No Reaction C00593/3 0x8100
 xx.0131.00000 0x1f00 7936 CE4: CAN Bus Off No Reaction C00592/2 0x8000
 xx.0184.00064 0x5440 21568 Ck16: Time overflow manual control Fault -
 xx.0135.00004 0x2304 8964 CP04: CAN RPDO4 No Reaction C00593/4 0x8100
 xx.0145.00035 0x2d23 11555 dF10: AutoTrip Reset Fault C00189 0xF000
 xx.0145.00014 0x2d0e 11534 dF14: SW/HW invalid Fault -
 xx.0145.00024 0x2d18 11544 dF18: BU RCOM error Fault - 0x6100
 xx.0145.00033 0x2d21 11553 dF21: BU Watchdog Fault - 0x6100
 xx.0145.00034 0x2d22 11554 dF22: CU watchdog Fault - 0x6100
 xx.0145.00025 0x2d19 11545 dF25: CU RCOM error Fault - 0x6100
 xx.0145.00050 0x2d32 11570 dF50: Retain error Fault - 0x6100
 xx.0400.00009 0x1a09 6665 dH09: EEPROM power section Fault - 0x5530
 xx.0400.00016 0x1a10 6672 dH10: Fan failure Warning C00566 0x5000
 xx.0400.00104 0x1a68 6760 dH68: Adjustment data error CU Fault - 0x5530
 xx.0400.00105 0x1a69 6761 dH69: Adjustment data error BU Fault - 0x5530
 xx.0123.00099 0x1763 5987 FC1: Field controller limitation No Reaction C00570/4 0xF000
 xx.0123.00094 0x175e 5982 FCH1: Switching frequency reduction No Reaction C00590 0x2000
 xx.0123.00095 0x175f 5983 FCH2: Max. speed for Fchop No Reaction C00588 0xF000
 xx.0123.00057 0x1739 5945 ID1: Motor data identification error WarningLocked - 0xF000
 xx.0123.00058 0x173a 5946 ID3: CINH motor data identification WarningLocked - 0xF000
 xx.0123.00059 0x173b 5947 ID4: Resistor identification error Warning - 0xF000