Lenze E84DSxxx - Manual (Page 354)

9 Diagnostics & error management
9.10 Error messages of the operating system
354
Lenze · 8400 protec StateLine · Reference manual · DMS 4.2 EN · 03/2013 · TD05
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
 xx.0125.00011 0x190b 6411 Io11: DigOut level Warning C00598/3 0xF000
 xx.0123.00145 0x1791 6033 LP1: Motor phase failure No Reaction C00597 0x3000
 xx.0123.00015 0x170f 5903 LU: DC bus undervoltage Trouble C00600/1 0x3100
 xx.0140.00013 0x280d 10253 MCI1: Module missing / incompatible No Reaction C01501/2 0x7000
 xx.0123.00016 0x1710 5904 OC1: Power section - short circuit Fault - 0x2000
 xx.0123.00017 0x1711 5905 OC2: Power section - earth fault Fault - 0x2000
 xx.0119.00050 0x1332 4914 OC5: Ixt overload Fault - 0x2000
 xx.0123.00105 0x1769 5993 OC6: I2xt motor overload Warning C00606 0x2000
 xx.0123.00007 0x1707 5895 OC7: Motor overcurrent Fault - 0x2000
 xx.0123.00030 0x171e 5918 OC10: Max. current reached Fault - 0x2000
 xx.0123.00071 0x1747 5959 OC11: Active clamp operation Warning - 0xF000
 xx.0123.00065 0x1741 5953 OC12: I2xt overload - brake resistor Fault - 0xF000
 xx.0123.00090 0x175a 5978 OC13: Max. current for Fch exceeded Fault - 0xF000
 xx.0123.00096 0x1760 5984 OC14: Direct-axis current controller limitation No Reaction C00570/1 0xF000
 xx.0123.00097 0x1761 5985 OC15: Cross current controller limitation No Reaction C00570/2 0xF000
 xx.0123.00098 0x1762 5986 OC16: Torque controller limitation No Reaction C00570/3 0xF000
 xx.0123.00031 0x171f 5919 OC17: Clamp sets pulse inhibit No Reaction C00569/1 0xF000
 xx.0119.00001 0x1301 4865 OH1: Heatsink overtemperature Fault - 0x4000
 xx.0119.00015 0x130f 4879 OH3: Motor temperature (X21) triggered Fault C00585 0x4000
 xx.0119.00000 0x1300 4864 OH4: Heatsink temp. > shutdown temp. -5°C No Reaction C00582 0x4000
 xx.0123.00032 0x1720 5920 OS1: Max. speed limit reached No Reaction C00579 0x8400
 xx.0123.00001 0x1701 5889 OT1: Max. torque reached No Reaction C00608 0x8300
 xx.0123.00093 0x175d 5981 OT2: Speed controller output limited No Reaction C00567 0xF000
 xx.0123.00014 0x170e 5902 OU: Überspannung Zwischenkreis Trouble - 0x3100
 xx.0144.00001 0x2c01 11265 PS01: No memory module Warning - 0x6300
 xx.0144.00002 0x2c02 11266 PS02: Invalid par. set Fault - 0x6300
 xx.0144.00003 0x2c03 11267 PS03: Invalid device par. set Fault - 0x6300
 xx.0144.00004 0x2c04 11268 PS04: Invalid MCI par. set Fault - 0x6300
 xx.0144.00007 0x2c07 11271 PS07: Invalid memory module par. set Fault - 0x6300
 xx.0144.00008 0x2c08 11272 PS08: Invalid device par. Fault - 0x6300
 xx.0144.00009 0x2c09 11273 PS09: Invalid par. format Fault - 0x6300
 xx.0144.00010 0x2c0a 11274 PS10: Memory module binding invalid Fault -
 xx.0123.00205 0x17cd 6093 SD3: Open circuit - feedback system Fault C00586 0x7300
 xx.0123.00200 0x17c8 6088 SD10: Speed limit - feedback system 12 Fault C00607 0x7300
 xx.0111.00002 0x0b02 2818 Su02: One mains phase is missing Warning C00565 0x3000
 xx.0111.00003 0x0b03 2819 Su03: Too frequent mains switching Fault - 0x3000
 xx.0111.00004 0x0b04 2820 Su04: CU Insufficiently Supplied Warning - 0x3000
 xx.0111.00005 0x0b05 2821 Su05: IO supply overload Warning C00598/4 0x3000
 xx.0980.00001 - - US01: User error 1 No Reaction C00581/1 0x6200
 xx.0981.00002 - - US02: User error 2 No Reaction C00581/2 0x6200
 xx.0982.00003 - - US03: User error 3 No Reaction C00581/3 0x6200
 xx.0983.00004 - - US04: User error 4 No Reaction C00581/4 0x6200
Error number Error message Response
(Lenze setting)
can be set in CAN Emergency
Error Code
32 bits 16 bits
hex
16 bits
dec