Rockwell Automation 1758-RTU202 DataSite Software User Manual FRN 1.2 - Manual (Page 10)

Publication 1758-UM002D-EN-P - October 2010
10 Table of Contents
Configure the DS DNP3 Database. . . . . . . . . . . . . . . . . . . . . . . . 248
Configure a DS DNP3 Channel . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Download the Configuration file . . . . . . . . . . . . . . . . . . . . . . . . . 256
Upload the Configuration file . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Save the Configuration file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Operation and Data Validation Example . . . . . . . . . . . . . . . . . . . . . . 258
Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
Chapter 4
Extension Modbus Protocol for
DataSite Controllers (1758-FLO) Modbus Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
Modbus Register Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
Modbus Registers for Physical I/O Hardware. . . . . . . . . . . . . . . 269
Modbus Registers used by the 1758-FLO Controllers . . . . . . . . 270
Modbus Registers for Contract Time . . . . . . . . . . . . . . . . . . . . . . 276
Modbus Registers for the Power Shutdown Time . . . . . . . . . . . . 277
Modbus Registers for Reading Gas Component Parameters . . . 277
Addresses Associated with the Extension Modbus Protocol Commands
281
Pass Code for User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Command List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
Command Number 1: Correct the System Time . . . . . . . . . . . . . 283
Command Number 2: Set the Pass Code . . . . . . . . . . . . . . . . . . . 284
Command Number 3: Set the Device Name . . . . . . . . . . . . . . . . 285
Command Number 4: Read the Device Name . . . . . . . . . . . . . . 285
Command Number 5: Disable/Enable the Flow Calculation . . . 286
Command Number 6: Read the Disable/Enable Flow Calculation
Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Command Number 7: Set the Transaction (Contract) Time. . . . 288
Command Number 8: Read the Transaction (Contract) Time . . 288
Command Number 9: Set Up the Input Signal Test . . . . . . . . . . 289
Command Number 10: Read the Input Signal Test. . . . . . . . . . . 290
Command Number 11: Disable/Enable the Accumulation
Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
Command Number 12: Read Disable/Enable Setting for
Accumulation Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
Command Number 13: Set the Input Parameters . . . . . . . . . . . . 292
Command Number 14: Read the Input Parameters . . . . . . . . . . 294
Command Number 15: Set the Alarm Range of Input Parameters .
295
Command Number 16: Read the Alarm Range of Input Parameters
297
Command Number 17: Set Up the Calculation Input Parameters . .
298
Command Number 18: Read the Calculation Input Parameter . 301
Command Number 19: Set Up the Gas Component Parameter. 303
Command Number 20: Read the Gas Component Parameter . . 307