Appendix, Index table – Lenze EPM−T9XX Modular system User Manual
Page 525
Index table
Appendix
15.1
L
15.1−11
EDSPM−TXXX−9.0−11/2009
Index
Important
Possible settings
Name
Selection
Lenze
I3004
h
¿
Config
analog/counter
module 4
00000000
h
{1
h
}
FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 4
·
I3004
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
·
I3004
h
is only available for the modular
system.
^ 12.3−1
^ 12.4−1
^ 12.5−1
^ 12.6−1
1
0
h
2
0
h
3
0
h
4
0
h
I3005
h
¿
Config
analog/counter
module 5
00000000
h
{1
h
}
FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 5
·
I3005
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
·
I3005
h
is only available for the modular
system.
^ 12.3−1
^ 12.4−1
^ 12.5−1
^ 12.6−1
1
0
h
2
0
h
3
0
h
4
0
h
I3006
h
¿
Config
analog/counter
module 6
00000000
h
{1
h
}
FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 6
·
I3006
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
·
I3006
h
is only available for the modular
system.
^ 12.3−1
^ 12.4−1
^ 12.5−1
^ 12.6−1
1
0
h
2
0
h
3
0
h
4
0
h
I3007
h
¿
Config
analog/counter
module 7
00000000
h
{1
h
}
FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 7
·
I3007
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
·
I3007
h
is only available for the modular
system.
^ 12.3−1
^ 12.4−1
^ 12.5−1
^ 12.6−1
1
0
h
2
0
h
3
0
h
4
0
h
I3008
h
¿
Config
analog/counter
module 8
00000000
h
{1
h
}
FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 8
·
I3008
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
·
I3008
h
is only available for the modular
system.
^ 12.3−1
^ 12.4−1
^ 12.5−1
^ 12.6−1
1
0
h
2
0
h
3
0
h
4
0
h
I3009
h
¿
Config
analog/counter
module 9
00000000
h
{1
h
}
FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 9
·
I3009
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
·
I3009
h
is only available for the modular
system.
^ 12.3−1
^ 12.4−1
^ 12.5−1
^ 12.6−1
1
0
h
2
0
h
3
0
h
4
0
h