Lenze EPM−T9XX Modular system - Manual (Page 539)

Total index
15
Appendix
15.3
L
15.3−7 EDSPM−TXXX−9.0−11/2009
Features, 4.1−1 , 4.2−1 , 4.3−1 , 4.4−1 , 4.5−1 , 4.6−1 ,
4.7−1 , 4.8−1 , 4.9−1 , 4.10−1 , 4.11−1 , 4.12−1 , 4.13−1
, 4.14−1 , 4.15−1 , 4.16−1 , 4.17−1 , 4.18−1 , 4.19−1 ,
4.20−1 , 4.21−1 , 4.22−1 , 4.23−1 , 4.24−1 , 5.1−1 ,
5.2−1 , 5.3−1 , 5.4−1
− 16xdig. I/O compact (single−wire conductor), 5.2−1
− 16xdig. I/O compact (three−wire conductor), 5.3−1
− 16xdigital input, 4.6−1
− 16xdigital output 1A, 4.10−1
− 1xcounter/16xdigital input, 4.23−1
− 2/4xcounters, 4.21−1
− 32xdig. I/O compact, 5.4−1
− 4xanalog input, 4.14−1
− 4xanalog input / output, 4.20−1
− 4xanalog output, 4.17−1
− 4xrelay, 4.12−1
− 8xdig. I/O compact, 5.1−1
− 8xdigital input, 4.5−1
− 8xdigital input / output, 4.13−1
− 8xdigital output 1A, 4.9−1
− 8xdigital output 2A, 4.11−1
− SSI interface, 4.22−1
− Terminal module, 4.24−1
G
General data, 3.1−1
GSE file, 10.4−1
H
Heartbeat, 8.7−1 , 9.7−1
Heartbeat Consumer, 8.7−1 , 9.7−1
Heartbeat Producer, 8.7−1 , 9.7−1
I
I/O system IP20, components
− Application as directed, 1.3−1
− Labelling, 1.3−1
Identifier, 8.1−2 , 9.1−2
Index, 8.4−3 , 9.4−3
Input data
− Transfer at 1xcounter/16xdigital input, 12.6−2 , 13.4−2
− Transmitting − SSI interface, 12.5−6 , 12.5−8 , 12.5−11
, 13.3−3
− transmitting with 2/4xcounter, 12.4−4 , 13.2−4
− transmitting with analog modules, 12.3−7 , 13.1−6
Installation, CE−typical drive system
− Assembly, 7.1−1
− Earthing, 7.1−1
− Shielding, 7.1−1
Installation, electrical, 7.1
Installation, mechanical, 6.1
Instruction code, 8.4−2 , 9.4−2
Insulation resistance, 3.1−1
Insulation voltage, 3.1−1
L
Labelling, Components of the I/O system IP20, 1.3−1
Legal regulations, 1.3−1
Liability, 1.3−2
Loading default setting, 12.8−1
M
Manufacturer, 1.3−1
Measured values, conversion for analog modules,
12.3−7 , 13.1−6
Mechanical installation, 6.1
Modular system
− Compatibility, with drive and automation components,
8.3−9 , 9.3−9
− Dimensions, 6.1−1
− Mounting dimensions, 6.1−1
Module
− Mounting on DIN rail, 6.1−2 , 6.2−2
− Remove from the backplane bus, 6.1−3
− Remove from the DIN rail, 6.2−2
Module identifiers, reading out, 8.10−3 , 9.10−3
Monitoring, 8.9−1 , 9.9−1
− Analog outputs, 8.9−3 , 9.9−3
Mounting, Module on the DIN rail, Mounting on DIN
rail, 6.1−2 , 6.2−2
Mounting conditions, 3.1−1
Mounting dimensions
− Compact system, 6.2−1
− Modular system, 6.1−1
Mounting place, 3.1−1
Mounting position, 3.1−1
N
Network management (NMT), 8.2−1 , 9.2−1
Network, CAN, Communication phases, 8.2−1 , 9.2−1
Networking
− CANopen, 9.1
− via system bus (CAN), 8.1
Node address
− Setting, 8.5−2 , 9.5−2
− Setting at the CAN Gateway, 4.1−3 , 5.1−3 , 5.2−3 ,
5.3−3 , 5.4−3
Node address setting, 4.2−2
Node Guarding, 8.6−1 , 9.6−1