Yaskawa SGDH Linear Sigma Series - Manual (Page 421)

Index
Index-1
INDEX
A
adjusting offset ....................................................................................38
air gap..................................................................................................14
alarm code output........................................................................... 76
, 2
alarm display table ................................................................................2
alarm display table when the application module is used.....................5
alarm reset ...................................................................................... 76
, 2
alarm traceback data clear (Fn006).....................................................13
alarm traceback data display (Fn000) ...................................................9
allocating input signals........................................................................27
allocating output signals......................................................................29
allowable maximum motor speed and dividing ratio monitor ............34
ALM....................................................................................................28
ALM-RST ...................................................................................... 27
, 3
ALO ....................................................................................................28
ambient/storage temperature .................................................................3
analog monitor ....................................................................................29
analog monitor cable...........................................................................10
analog monitoring .................................................................................4
application module..............................................................................10
application module detection results clear (Fn014) ............................19
automatic offset-signal adjustment of motor current detection signal
(Fn00E) ...............................................................................................14
autotuning functions..............................................................................3
B
base-mounted type ..............................................................................14
bias setting.............................................................................................3
BK .......................................................................................................28
built-in open collector power supply ....................................................3
built-in panel operator...........................................................................2
C
cable seletion.........................................................................................7
cables for analog monitor....................................................................19
cables for connecting hall sensors
dimensional drawings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
cables for connecting linear scales
dimensional drawings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
cables for connecting personal computers ..........................................18
cables for connecting serial converter units
dimensional drawings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
calculating the required capacity of regenerative resistors ...................4
CE marking .........................................................................................11
checking products .................................................................................2
clear signal form selection ..................................................................48
CLR.....................................................................................................27
CLT .....................................................................................................28
CN1
terminal layout- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 26
CN2
terminal layout- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
coil assembly
model designations- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
COIN...................................................................................................28
connecting a reactor ............................................................................ 38
connecting linear scales
linear scale by Heidenhain - - - - - - - - - - - - - - - - - - - - - - - - -22
linear scale by Renishaw- - - - - - - - - - - - - - - - - - - - - - - - - - -22
connecting regenerative resistors........................................................ 39
connecting the digital operator ............................................................. 2
connection cable for digital operator .................................................. 10
connection cable for personal computer ............................................. 10
connection to host controller............................................................... 16
connector terminal block converter unit ............................................. 20
connectors and cables for encoder signals .......................................... 10
continuous output current ..................................................................... 2
control method ...................................................................................... 3
control mode selection ................................................................. 29
, 74
D
DATA/ENTER key ............................................................................... 3
DATA/SHIFT key ................................................................................. 3
DC reactors ......................................................................................... 28
selection- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -12
DeviceNet application module............................................................ 31
digital operator............................................................................. 10
, 18
key names and functions - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
status display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
types - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
DOWN key ........................................................................................... 3
DSPL/SET key...................................................................................... 3
dynamic brake....................................................................................... 4
E
electronic gear....................................................................................... 4
electronic gear ratio equation.............................................................. 51
encoder signal output .......................................................................... 43
external force limit.............................................................................. 69
external regenerative resistor .............................................................. 21
F
feed forward compensation................................................................... 3
feedback signal checking ............................................................... 9
, 15
feed-forward reference........................................................................ 15
flexible cables ..................................................................................... 10
wiring precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -10
force control tolerance .......................................................................... 3
force limit setting ......................................................................... 11
, 17
force limiting using an analog voltage reference................................ 71
forward run prohibited ........................................................................ 32
frequency characteristics....................................................................... 3
fuse capacity ....................................................................................... 11
G
grounding ............................................................................................ 33
H
hall sensor
selecting no hall sensor- - - - - - - - - - - - - - - - - - - - - - - - - - - -14
hall sensor signal monitor ................................................................... 35
hot start ............................................................................................... 12
I
I/O signal (CN1) names and functions ............................................... 27
I/O signal cables........................................................................... 10
, 15