Rockwell Automation 284E ArmorStart with EtherNet/IP - User Manual User Manual
Page 195
Rockwell Automation Publication 280E-UM001B-EN-P – July 2012
195
Bulletin 280E/281E/284E Programmable Parameters Chapter 7
44
OutB Net IdlValue
This parameter determines the state that Output B
assumes when the network is idle and Parameter 43
(OutB Net IdlState) is set to “0”.
0 = Open
User I/O Configuration
Common
45
Keypad Mode
This parameter selects if the keypad operation is
maintained or momentary.
0 = Maintained
Misc. Configuration
Common
46
Keypad Disable
This parameter disables all keypad function except for
the OFF and RESET buttons.
0 = Not Disabled
Misc. Configuration
Common
47
Set To Defaults
This parameter if set to 1 will set the device to the
factory defaults.
0 = No Operation
Misc. Configuration
Common
48
Drive Control
This parameter provides the status of drive parameters.
0
Drive I/O Configuration
284E
49
DrvIn Pr FltState
This parameter, in conjunction with Parameter 50
(DrvIn Pr FltValue), defines how the Drive Digital Inputs
1…4 will respond when a protection trip occurs.
0 =
Go to PrFlt Value
Drive I/O Configuration
284E
50
DrvIn Pr FltValue
This parameter determines the state of Drive Digital
Inputs 1…4, assumes when a trip occurs.
0 = Open
Drive I/O Configuration
284E
51
DrvIn Net FltState
This parameter, in conjunction with Parameter 52
(DrvIn Net FltValue), defines how the Drive Digital
Inputs 1…4 will respond when a network fault occurs.
0 =
Go to Fault Value
Drive I/O Configuration
284E
52
DrvIn Net FltValue
This parameter determines the state of Drive Digital
Inputs 1…4 when a network fault occurs and
Parameter 51 (DrvIn Net FltState) is set to “0”.
0 = OFF
Drive I/O Configuration
284E
53
DrvIn Net FItState
This parameter, in conjunction with Parameter 54
(DrvIn Net FItValue), defines how the Drive Digital
Inputs 1…4 will respond when a DeviceNet™ network
is idle.
0 =
Go to Fault Value
Drive I/O Configuration
284E
54
DrvIn Net FItValue
This parameter determines the state that Drive Digital
Inputs 1…4 assume when the network is idle and
Parameter 53 (DrvIn Net FItState) is set to “0”.
0 = OFF
Drive I/O Configuration
284E
55
High Speed Enaable
This parameter enable High Speed Inverter control thru
the terminal block.
0 = Disabled
Drive I/O Configuration
284E
56
Base Enclosure
Indicates the ArmorStart Base unit enclosure rating.
1
Basic Status
Common
57
Base Options
Indicates the options for the ArmorStart Base unit.
0
Basic Status
Common
58
Wiring Options
This parameter provides the Wiring Options.
0
Basic Status
Common
59
Starter Enclosure
This parameter provides the Starter Enclosure.
1
Basic Status
Common
60
Starter Options
This parameter provides the Starter Options.
0
Basic Status
Common
61
Last PR Fault
This parameter provides the Last PR Fault.
0 = None
Basic Status
Common
62
Warning Status
This parameter provides the Warning Status.
0
Basic Status
Common
63
Base Trip
This parameter provides the Base Module Trip Status.
0
Basic Status
Common
101
Phase A Current
This parameter provides the current of Phase A.
0
Starter Display
DOL
102
Phase B Current
This parameter provides the current of Phase B.
0
Starter Display
DOL
103
Phase C Current
This parameter provides the current of Phase C.
0
Starter Display
DOL
104
Average Current
This parameter provides the average current.
0
Starter Display
DOL
Table 28 - ArmorStart Common Parameters
Parameter
Number
Parameter Name
Description
Factory Default
Group
Controller