Yaskawa AC Drive Z1000 Bypass Technical Manual - Manual (Page 451)

Index
+
+V..............................................................................71
Numerics
5th Most Recent Fault..................................................... 338
A
A/D Conversion Error..................................................... 225
A1 ..............................................................................71
A1-04 ........................................................................ 253
A1-05 ........................................................................ 253
A2 ..............................................................................71
AC .............................................................................71
Accel/Decel Time.................................................... 220, 300
Acceleration Error ......................................................... 250
Acceleration Time ......................................................... 139
Adjusted Slip Calculation Error ......................................... 249
AL02......................................................................... 239
AL03......................................................................... 239
AL04......................................................................... 239
AL13......................................................................... 239
AL14......................................................................... 239
AL16......................................................................... 240
Alarm Causes and Solutions ............................................. 239
Alarm Outputs for Maintenance Monitors ............................. 268
Alarm Register 007FH Contents......................................... 400
Alarms and Errors ......................................................... 221
Allowable Frequency Fluctuation ..................... 296, 297, 298, 299
Allowable Voltage Fluctuation ........................ 296, 297, 298, 299
ALM LED Light .............................................................92
Altitude..................................................................40, 300
Ambient Temperature .................................................40, 300
Analog Filter Time Constant ............................................. 220
Analog Input Filter Time Constant ...................................... 162
Analog Input Objects...................................................... 364
Analog Input Terminal Enable Selection ............................... 163
Analog Output Objects.................................................... 364
Analog Value Objects ..................................................... 364
Apogee FLN Cable Loss Behavior ...................................... 413
APOGEE FLN Cable Specifications.................................... 406
APOGEE FLN Communications ........................................ 404
APOGEE FLN Point Number Summary ............................... 409
Application Presets ........................................................ 108
Application Selection ..................................................... 108
Area of Use ................................................................. 300
AUTO Key ...................................................................92
AUTO LED and HAND LED Indications ...............................95
AUTO Light ..................................................................92
Auto Restart Fault Output Operation Selection........................ 174
Auto Restart Operation Selection........................................ 325
Auto-Tuning .......................................................... 111, 114
Auto-Tuning Codes........................................................ 249
Auto-Tuning Errors........................................................ 223
Auto-Tuning Fault Codes................................................. 112
Auto-Tuning Fault Detection............................................. 249
Auto-Tuning Fault Solutions............................................. 249
Auto-Tuning for Induction Motors ...................................... 111
Auto-Tuning Input Data ............................................ 111, 112
Auto-Tuning Interruption Codes......................................... 112
Auto-Tuning Mode Selection ...................................... 114, 332
B
BACnet Configuration .................................................... 356
BACnet Objects Supported............................................... 363
BACnet Serial Communication .......................................... 360
BACnet Setup Parameters ................................................ 360
BACnet Specifications .................................................... 357
Baseblock ................................................................... 240
Basic Auto-Tuning Preparations......................................... 111
BAS Interlock Open ....................................................... 239
bAT .......................................................................... 224
bb............................................................................. 240
Bi-Directional Speed Search Selection ................................. 126
Binary Input Objects ...................................................... 365
Binary Output Objects .................................................... 366
Binary Value Objects...................................................... 366
Braking Torque ............................................................ 300
Broadcast Messages ....................................................... 398
bUS .................................................................... 224, 240
Bypass Controller Active Faults Register 1 ............................ 334
Bypass Controller Active Faults Register 2 ............................ 335
Bypass Controller Status Register 1..................................... 334
Bypass Controller Status Register 2..................................... 334
Bypass Control System ................................................... 195
Bypass Digital Input Invert Settings .................................... 209
Bypass Digital Input States............................................... 334
Bypass Digital Input Terminal Settings........................... 207, 209
Bypass Digital Output States............................................. 334
Bypass Model Enclosure Dimensions ...........................44, 46, 48
Bypass Nameplate ...........................................................29
Bypass Operations by BACnet........................................... 362
Bypass Operations by MEMOBUS/Modbus........................... 382
Bypass Operations by N2................................................. 425
Bypass Parameters......................................................... 195
YASKAWA ELECTRIC SIEP YAIZ1B 01D YASKAWA AC Drive – Z1000 Bypass Technical Manual 451