Yaskawa AC Drive Z1000 Bypass Technical Manual User Manual
Page 457
Reattaching the Front Cover ....................................................79
Reattaching the Terminal Cover ................................................74
Removing the Cooling Fan .................................................... 273
Removing the Front Cover ......................................................75
Removing the Terminal Cover..................................................73
Replacement Parts .............................................................. 267
RESET Key........................................................................92
Resistance Tuning Error ....................................................... 249
Response Messages from Drive to Master ............................ 383, 429
Restart Enabled ................................................................. 159
Return Fan with PI Control Application..................................... 108
Reverse Operation Selection .................................................. 121
Reverse Operation Selection 2 by PI Output................................ 137
Rotational Auto-Tuning for V/f Control..................................... 111
RS-485 Interface ................................................................ 379
Run Command/Frequency Reference Source Selection Error............ 247
Run Command Selection ...................................................... 254
Run Command Source Selection ............................................. 341
S
S: Special Parameters .................................................... 186, 330
S/L2.................................................................................62
S1: Dynamic Noise Control Function........................................ 330
S2: Sequence Timers ..................................................... 187, 330
SAFE ............................................................................. 244
Safety Open Message Selection .............................................. 210
Safety Standard ................................................................. 300
S-Curve Characteristics .................................................. 139, 220
SE ................................................................................. 244
Selecting the Type of Auto-Tuning .......................................... 112
Sequence Timer 1............................................................... 187
Sequence Timer 1 Day Selection ............................................. 330
Sequence Timer 1 Reference Source......................................... 330
Sequence Timer 1 Selection................................................... 330
Sequence Timer 1 Start Time ................................................. 330
Sequence Timer 1 Stop Time ................................................. 330
Sequence Timer 2 Day Selection ............................................. 331
Sequence Timer 2 Reference Source......................................... 331
Sequence Timer 2 Selection................................................... 331
Sequence Timer 2 Start Time ................................................. 330
Sequence Timer 2 Stop Time ................................................. 331
Sequence Timer 3 Day Selection ............................................. 331
Sequence Timer 3 Reference Source......................................... 331
Sequence Timer 3 Selection................................................... 331
Sequence Timer 3 Start Time ................................................. 331
Sequence Timer 3 Stop Time ................................................. 331
Sequence Timer 4 Day Selection ............................................. 332
Sequence Timer 4 Reference Source......................................... 332
Sequence Timer 4 Selection................................................... 332
Sequence Timer 4 Start Time ................................................. 331
Sequence Timer 4 Stop Time ................................................. 331
Sequence Timer Error .......................................................... 248
Sequence Timers 1/2/3/4 Reference Source................................. 189
Sequence Timers 1/2/3/4 Selection........................................... 188
Sequence Timers 1 to 4 Day Selection....................................... 188
Sequence Timers 1 to 4 Start Time........................................... 188
Sequence Timers 1 to 4 Stop Time ........................................... 188
Sequence Timers 2 to 4 ........................................................ 188
SEr ................................................................................ 236
Serial Comm Fault.............................................................. 239
Serial Communication Fault Detection Selection .......................... 424
Serial Communications Cable Connection Terminal (TB3) .. 358, 378, 421
Serial Communications Fault Time Select .................................. 424
Serial Communications Node Address Select .............................. 423
Serial Communications Protocol Select ..................................... 423
Serial Communications Receive to Transmit Wait Time.................. 424
Serial Communication Terminals...............................................72
Serial Communication Transmission Error ................................. 240
Setup Mode ...................................................................... 101
Shielded Twisted-Pair Cables ...................................................84
Simplified Setup Using the Quick Setting Group .......................... 101
Slave Address ................................................................... 384
Smoke Purge in Bypass ........................................................ 239
Smoke Purge in Drive.......................................................... 239
Soft Charge Bypass Relay Maintenance..................................... 340
Soft Charge Bypass Relay Maintenance Time.............................. 242
Soft Starter Speed Reference at Previous Fault............................. 337
Software No. (Flash) ........................................................... 337
Software No. (ROM) ........................................................... 337
Software version ..................................................................29
Speed Agree 1 ................................................................... 154
Speed Agree 2 ................................................................... 157
Speed Control Range ........................................................... 300
Speed Estimation Type Speed Search........................................ 123
Speed Search .................................................................... 119
Speed Search Deactivation Current .......................................... 125
Speed Search Deceleration Time ............................................. 125
Speed Search Delay Time ..................................................... 125
Speed Search Detection Compensation Gain ............................... 126
Speed Search Method Selection .............................................. 127
Speed Search Method Switching Level (Speed Estimation Type) ....... 126
Speed Search Restart Current Level.......................................... 127
Speed Search Restart Detection Time........................................ 127
Speed Search Selection at Start ............................................... 125
Speed Search Wait Time....................................................... 127
Stall Prevention ..................................................... 170, 220, 300
Stall Prevention Level during Acceleration ........................... 170, 324
Stall Prevention Level during Run ..................................... 172, 325
Stall Prevention Limit during Acceleration ........................... 171, 324
Stall Prevention Selection during Deceleration....................... 171, 325
Standard Connection Diagram ..................................................52
Starting Torque.................................................................. 300
Start Speed Search Select...................................................... 127
Stationary Auto-Tuning........................................................ 112
Stationary Auto-Tuning for Line-to-Line Resistance ...................... 111
Status Display ................................................................... 103
STo ............................................................................... 236
Stopping Method after Communication Error .............................. 167
Stopping Method Selection.................................................... 119
Storage Temperature .......................................................40, 300
Supported Properties of Objects .............................................. 363
Surrounding Area .................................................................40
Swing PWM ..................................................................... 140
T
T/L3.................................................................................62
T1-03 ............................................................................. 113
T1-04 ............................................................................. 113
T1-05 ............................................................................. 113
T1-06 ............................................................................. 113
Index
YASKAWA ELECTRIC SIEP YAIZ1B 01D YASKAWA AC Drive – Z1000 Bypass Technical Manual
457