Rockwell Automation 21G PowerFlex 750-Series AC Drives Programming Manual - Manual (Page 181)

Rockwell Automation Publication 750-PM001J-EN-P - October 2014 181
Drive Port 0 Parameters Chapter 3
Fil
e
Gr
ou
p
No. Display Name
Full Name
Description Values
Re
ad
-Write
Da
ta T
ype
AP
PL
IC
AT
IONS
Pump Jac
k
1165 Rod Speed
Rod Speed
Displays the speed in RPM of the pump rod after the gearbox and sheaves.
Rod Speed = Motor Speed x P1174 [Total Gear Ratio] Units:
Default:
Min/Max: RPM
0.00
0.00 / 10000.00 RO Real
1166 Rod Torque
Rod Torque
Displays the load side torque. P1174 [Total Gear Ratio] must be greater than zero to
activate this display. Units:
Default:
Min/Max: FtLb
0.00
0.00 / 10000.00 RO Real
1167 Rod Speed Cmd
Rod Speed Command
Displays the commanded speed in RPM of the pump rod after the gearbox and sheaves. Units:
Default:
Min/Max: RPM
0.00
0.00 / 10000.00 RO Real
1168 TorqAlarm Action
Torque Alarm Action
Sets the drive action when the Torque Alarm is exceeded. Note: only active with PC
pump applications. See P1179 [OilWell Pump Cfg]. Default:
Options: 0 = “Ignore”
0 = “Ignore”
1 = “Preset Spd1” RW 32-bit
Integer
1169 TorqAlarm Config
Torque Alarm Configure RW 16-bit
Integer
Enables the Torque Alarm function.
1170 TorqAlarm Dwell
Torque Alarm Dwell
Sets the time that the torque must exceed P1171 [TorqAlarm Level] before P1168
[TorqAlarm Action] takes place.
Active when P1169 [TorqAlarm Config] Bit 0 “Torque Level” = 1 (enabled). Units:
Default:
Min/Max: Secs
0.0
0.0 / 60.0 RW Real
1171 TorqAlarm Level
Torque Alarm Level
Sets the level at which the Torque Alarm becomes active.
Active when P1169 [TorqAlarm Config] Bit 0 “Torque Level” = 1 (enabled) Units:
Default:
Min/Max: FtLb
0.0
0.0 / 5000.0 RW Real
1172 TorqAlm Timeout
Torque Alarm Time Out
Sets the amount of time a Torque Alarm can be active until timeout action begins.
Active when P1169 [TorqAlarm Config] Bit 0 “Torque Level” = 1 (enabled) Units:
Default:
Min/Max: Secs
0.0
0.0 / 600.0 RW Real
1173 TorqAlarm TOActn
Torque Alarm Time Out Action
Sets the drive action when P1172 [TorqAlrm Timeout] is exceeded.
Active when P1169 [TorqAlarm Config] Bit 0 “Torque Level” = 1 (enabled)
“Ignore” (0) – No action is taken.
“Alarm” (1) – Type 1 alarm indicated.
“Flt Minor” (2) – Minor fault indicated. If running, drive continues to run.
Enable with P950 [Minor Flt Cfg]. If not enabled, acts like a major fault.
“FltCoastStop” (3) – Major fault indicated. Coast to Stop.
“Flt RampStop” (4) – Major fault indicated. Ramp to Stop.
“Flt CL Stop” (5) – Major fault indicated. Current Limit Stop. Default:
Options: 0 = “Ignore”
0 = “Ignore”
1 = “Alarm”
2 = “Flt Minor”
3 = “FltCoastStop”
4 = “Flt RampStop”
5 = “Flt CL Stop”
6 = “Resume” RW 32-bit
Integer
Options
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
To
rq
ue
L
ev
el
Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 = Disabled
1 = Enabled