Rockwell Automation 21G PowerFlex 750-Series AC Drives Programming Manual - Manual (Page 89)

Rockwell Automation Publication 750-PM001J-EN-P - October 2014 89
Drive Port 0 Parameters Chapter 3
DR
IVE CFG
Au
to M
an
u
al Ct
rl
329 Alt Man Ref AnHi
Alternate Manual Reference Analog High
Hi scale for the alternate manual speed reference when P328 [Alt Man Ref Sel] is
connected to an Analog Input. Units:
Default:
Min/Max:
Hz
RPM
P520
P521 / P520 RW Real
330 Alt Man Ref AnLo
Alternate Manual Reference Analog Low
Lo scale for the alternate manual speed reference when P328 [Alt Man Ref Sel] is
connected to an Analog Input. Units:
Default:
Min/Max:
Hz
RPM
0
P521 / P520 RW Real
331 Manual Preload
Manual Preload RW 16-bit
Integer
Enables/disables automatic preloading of the “Auto” speed reference into a HIM when the HIM has been granted Manual control while in Auto mode. See P935
[Drive Status 1] Bit 9 “Manual” to verify the operating condition of the drive. Important: Preload will only occur if the transfer from auto to manual is done while
the drive is running.
Fi
le
Grou
p
No. Display Name
Full Name
Description Values
Re
ad
-W
ri
te
Da
ta
T
ype
Options
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Po
rt
3
Po
rt
2
Po
rt
1
Re
se
rv
ed
Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 = Disabled
1 = Enabled
Fil
e
Gr
ou
p
No. Display Name
Full Name
Description Values
Re
ad
-Write
Da
ta
T
yp
e
DR
IV
E C
FG
Driv
e Mem
or
y
336 Reset Meters
Reset Meters
Resets selected meters to zero. The value will automatically be returned to 0.
“MWH and kWh” (1) – Resets P13 [Elapsed MWH], P14 [Elapsed kWH], P16 [Elpsd Mtr
MWHrs], P17 [Elpsd Rgn MWHrs], P18 [Elpsd Mtr kWHrs], and P19 [Elpsd Rgn kWHrs].
“Elapsed Time” (2) – Resets P15 [Elapsed Run Time]. Default:
Options: 0 = “Ready”
0 = “Ready”
1 = “MWH and kWh”
2 = “Elapsed Time” RW 32-bit
Integer
Fil
e
Gr
oup
No. Display Name
Full Name
Description Values
Read-W
rite
Da
ta
T
yp
e
DR
IVE CFG
St
ar
t F
ea
tur
es
345 Start At PowerUp
Start At Power Up
Enables/disables a feature to issue a Run command and automatically resume running
at commanded speed after drive input power is restored. Requires a digital input, P163
[DI Run], P164 [DI Run Forward], or P165 [DI Run Reverse], is configured for Run and a
valid start contact. Default:
Options: 0 = “Disabled”
0 = “Disabled”
1 = “Enabled” RW 32-bit
Integer
346 PowerUp Delay
Power Up Delay
Defines the programmed delay time, in seconds, before a start command is accepted
after power up. Units:
Default:
Min/Max: Secs
0.00
0.00 / 10800.00 RW Real
ATTENTION: Equipment damage and/or personal injury may result if this parameter is used in an inappropriate
application. Do not use this function without considering applicable local, national and international codes, standards,
regulations or industry guidelines.