Yaskawa iQpump Controller Programming Manual - Manual (Page 146)

146 YASKAWA TM.iQp.07 iQpump Controller Programming Manual
The iQpump drive can be configured to program the drive using units or scaling that are appropriate for the pumping system by
programming the System Units (P1-02). The System Units will affect setpoint references, feedback scaling, pump levels, and display
monitors. The following is a list of parameters that are affected by the programming of the System Units (P1-02).
• d1 Group: d1-01 through d1-04.
• o1 Group: o1-07, o1-08.
• P1 Group: P1-03, P1-04, P1-07, P1-09, P1-11, P1-13.
• P2 Group: P2-02, P2-04, P2-09, P2-10, P2-15, P2-16.
• P3 Group: P3-03, P3-05, P3-07, P3-08, P3-12, P3-14.
• P4 Group: P4-01
• U1 Monitor: U1-91
For further description of each parameter, please refer to the appropriate section or Appendix A.
(*su1) When P1-02 = 13, parameter P1-03 will have to be set to (120 x E1-04 / E2 / 04) for proper display. When P1-02 = 14, parameter
P1-03 will have to be set to the same value as E1-04 for proper display.
<0034>
Table 52 Related Parameters <0034>
◆ P1-03 Feedback Device Scaling
Setting Range: 1 ~ 36000 [based on System Units (P1-02)
Factory Default: 00145 psi
The iQpump drive can be configured to scale the feedback signal using the Feedback Device Scaling Parameter (P1-03). The
programmed value in P1-03 represents the maximum level when a feedback reference is provided to the drive. An example: If a 4-20 mA
signal is provided and P1-03 is set to 145 psi, then 20 mA would represent the maximum psi readout level of 145 psi. This parameter
works in conjunction with the System Units (P1-02).
3 F: Degrees Fahrenheit
4 CFM: Cubic ft / min
5 CMH: Cubic m / hr
6 LPH: Liters / hr
7 LPS: Liters / s
8 Bar: Bar
9 Pa: Pascals
10 C: Degrees Celsius
11 ft: Feet <0032>
12 %: Percent
13 rpm: Revs / min (*su1) <0034>
14 Hz: Hertz (*su1) <0034>
Parameter
No.
Addr.
Hex
Parameter Name
Digital Operator Display
Description Range Default
Menu
Location
P1-02 601
System Units
System Unit
0: WC: Inch of Water
1: psi: lb / SqrInch
2: GPM: Gallons / min
3: F: DegFarenheit
4: CFM: Cubic ft / min
5: CMH: Cubic m / hr
6: LPH: Liters / hr
7: LPS: Liters / s
8: Bar: Bar
9: Pa: Pascals
10: C: Deg Celsius
11: Mtr: Meters
12:%: Percent
13: rpm: Revs / min (*su 1)
14: Hz: Hertz(*su 1)
0 ~ 14 1 Programming
(*su1) When P1-02 = 13, parameter P1-03 will have to be set to (120 * E1-04 / E2-04) for proper display. When P1-02 = 14, parameter P1-03 will have to be set to the
same value as E1-04 for proper display.
X X X X X
Digit 5 Digit 4 Digit 3 Digit 2 Digit 1
Setting Description