Yaskawa VS-626 MC5 - Manual (Page 226)

User Constants
8.2.5 Options Constants: F
- 18
Constant
Name
Setting Factory
Change
during
Control Methods
Constant
Number Display
Description
Setting
Range
Factory
Setting
g
during
Opera-
tion
Open Loop
Vector
Flux Vector
Page
F1-10
Excessive speed
deviation detection
level Sets the speed deviation detection
method.
Any speed deviation above the
F1-10 set level (set as a percentage
0 to 50 10 A - 24
PG Deviate Level
F1-10 set level (set as a percentage
of the maximum output frequency),
which continues for the deviation
F1-11
Excessive speed
deviation detection
delay time
which continues for the deviation
detection time (F1-11) is detected
as a speed deviation.
Speed deviation is the difference
b t t l t d d
0.0 to
10.0 0.5 A - 24
PG Deviate Time
p
between actual motor speed and
the reference command speed.
10.0
F1-14
PG open-circuit
detection time Used to set the PG disconnection
detection time. PGO will be de-
tected if the detection time contin-
0.0 to
10 0
2.0 A - 23 F1 14
PGO Time
tected if the detection time contin-
ues beyond the set time. 10.0
2.0 A 23
J Other Options Setup: F2 through F9
F2: Analog Reference Card F6: DO-08 Digital Output Card
F3: Digital Reference Card F7: Pulse Monitor Card
F4: Analog Monitor Card F8: SI-F/G
F5: DO-02 Digital Output Card F9: DOS/SI-B
Constant
Name
Setting Factory
Change
during
Control Methods
Constant
Number Display
Description
Setting
Range
Factory
Setting
g
during
Opera-
tion
Open Loop
Vector
Flux Vector
Page
F2-01
Bi-polar or uni-polar
input selection
Sets the functions for channel 1 to 3
which are effective when the
AI-14B Analog Reference Card is
used.
0: 3-channel individual (Channel
1: terminal 13, Channel 2: ter-
minal 14, Channel 3: terminal
16)
0 1 0 B B - 27 F2 01
AI-14 Input Sel
)
1: 3-channel addition (Addition
values are the frequency refer-
ence)
When set to 0, select 1 for b1-01.
In this case the multi-function in-
put “Option/Inverter selection”
cannot be used.
0 1 0 B B - 27
F3-01
Digital input option
Sets the Digital Reference Card in-
put method.
0: BCD 1% unit
1: BCD 0.1% unit
2: BCD 0.01% unit
3: BCD 1 Hz unit
4
BCD 0 1 H it 0 to 7 0 B B 28 F3-01
DI Input
4: BCD 0.1 Hz unit
5: BCD 0.01 Hz unit
6: BCD special setting (5-digit in-
put)
7: Binary input
6 is only effective when the
DI-16H2 is used.
0 to 7 0 B B - 28
F4-01
Channel 1 monitor
selection Effective when the Analog Monitor
Card is used.
Monitor selection:
1 to 33 2 B B - 28 F4 01
AO Ch1 Select
Monitor selection:
Set the number of the monitor
item to be output (U1-
)
1 to 33 2 B B - 28
F4-02
Channel 1 gain
item to be output. (U1- )
Gain:
S t th lti l f 10 V f t
0.00 to
1 00 B B 28 F4-02
AO Ch1 Gain
Set the multiple of 10 V for out-
putting monitor items.
0.00 to
2.50
1.00 B B - 28
F4-03
Channel 2 monitor
selection
p g
4, 10, 11, 12, 13, 14, 25, 28 can-
not be set. 29 to 31 are not used.
When the AO-12 is used outputs
f 10 V ibl I hi
1 to 33 3 B B - 28 F4 03
AO Ch2 Select
When the AO 12 is used outputs
of
r 10 V are possible. In this
case, set H4-07 (select multi-
f
i l i l
1 to 33 3 B B - 28
F4-04
Channel 2 gain
case, set H4 07 (select multi
function analog output signal
level) to 1. When the AO-08 is
d l t t f 0 t 10 V
0.00 to
0 50 B B 28 F4-04
AO Ch2 Gain
) W O
used, only outputs of 0 to +10 V
are possible.
0.00 to
2.50
0.50 B B - 28
8