Yaskawa VS-626 MC5 - Manual (Page 76)

4.2Modes
- 13
Func-
tion
Valid Access Levels
Min.
Unit
Output Signal Levels for
Multi-function Analog Out-
puts
Function
Name Con-
stant
No.
Func-
tion Flux
Vector
Open Loop
Vector
Min.
Unit
Output Signal Levels for
Multi-function Analog Out-
puts
Function Digital Operator
Display
Con-
stant
No.
U1-12
Operation status
Inverter operating status.
U1-12 = 0 0 0 0 0 0 0 0
1: Running
1: Zero-speed level
1: Reverse Can’t be output Q Q U1-12
Int Ctl Sts 1
1: Reverse
1: Reset input ON
1: F.ref/F.out agree
1: Inverter ready
1: Minor fault detected
1: Major fault detected
Can’t be output. Q Q
U1-13
Cumulative opera-
tion time
Monitors the Inverter’s elapsed
operating time.
The initial value and running/
power on time selection can be
Can’t be output. 1 hr Q Q U1 13
Elapsed Time
g
power-on time selection can be
set with user constants o2-07
and o2-08.
Can t be output. 1 hr Q Q
U1-14
Software No.
Manufacturer’s ID number Can’t be output Q Q U1-14
FLASH ID
Manufacturer’s ID number Can’t be output. Q Q
U1-15
Terminal 13 input
voltage level Monitors the input voltage of
the frequency reference (volt-
age).
10 V: 100% (10 V)
(0 to
r10 V possible)
0.1 % B B U1 15
Term 13 Level
age).
An input of 10 V corresponds to
100%.
(0 to r10 V possible)
0.1 % B B
U1-16
Terminal 14 input
current level Monitors the input current of the
frequency reference (current).
An inp t of 20 mA corr sponds
20 mA: 100% (20 mA)
(0 to +10 V output)
0.1 % B B U1 16
Term 14 Level
An input of 20 mA corresponds
to 100%. (0 to +10 V output)
0.1 % B B
Status
Moni-
tor
U1-17
Terminal 16 input
voltage level Monitors the input voltage of
the multi-function analog input.
An inp t of 10 V corr sponds to
10 V: 100% (10 V)
(0 to
r10 V possible) 0.1 % B B
tor
U1 17
Term 16 Level
An input of 10 V corresponds to
100%. (0 to r10 V possible) 0.1 % B B
U1-18
Motor secondary
current (lq) Monitors the calculated value of
the motor’s secondary current
(Iq).
10 V: Rated secondary cur-
rent
0.1 % B B U1 18
Mot SEC Current
(Iq).
The motor’s rated secondary
current corresponds to 100%. e t
(0 to +10 V output)
0.1 % B B
U1-19
Motor exciting cur-
rent (ld) Monitors the calculated value of
the motor’s excitation current
(Id).
10 V: Rated secondary cur-
rent
0.1 % B B U1 19
Mot EXC Current
(Id).
The motor’s rated secondary
current corresponds to 100%. e t
(0 to +10 V output)
0.1 % B B
U1-20
Output frequency
after soft-start
Monitors the output frequency
after a soft start.
The display shows the frequen-
cy without the correction from
10 V: Max. frequency
(0 to
r10 V possible)
0.01
Hz A A U1 20
SFS Output
p y q
cy without the correction from
compensation functions such as
slip compensation. (0 to r10 V possible) Hz A A
U1-21
ASR input Monitors the input to the speed
control loop.
10 V: Max. frequency
0 01 % A U1-21
ASR Input
co t o oop.
The max. frequency corresponds
to 100%. 10 V: Max. frequency
(0 to
r10 V possible)
0.01 % A
U1-22
ASR output Monitors the output from the
speed control loop.
10 V: Rated secondary cur-
rent
0 01 % A U1-22
ASR Output
speed co t o oop.
The motor’s rated secondary
current corresponds to 100%.
rent
(0 to
r10 V possible)
0.01 % A
U1-23
Speed deviation Monitors the speed deviation
within the speed control loop.
10 V: Max. frequency
0 01 % A U1-23
Speed Deviation
w t t e speed co t o oop.
The max. frequency corresponds
to 100%.
10 V: Max. frequency
(0 to
r10 V possible)
0.01 % A
4