Yaskawa VS-626 MC5 - Manual (Page 229)

8.2 Programming Mode Constants
- 21
Setting
value Page
Control Methods
Function
Setting
value Page
Flux vector
Open loop
Vector
Function
81 MC answerback (N.C.) - 68
82 MC answerback (N.O.) - 68
J Multi-function Outputs: H2
Constant Setting Factory
Change
during
Control Methods
Constant
Number
Name Display
Setting
Range
Factory
Setting
g
during
Opera-
tion
Open Loop
Vector
Flux Vector
Page
H2-01
Multi-function input
(terminal 9-10)
Terminal 9 Sel 0 to 37 0 B B - 42
H2-02
Multi-function input
(terminal 25-27)
Terminal 25 Sel 0 to 37 1 B B - 42
H2-03
Multi-function input
(terminal 26-27)
Terminal 26 Sel 0 to 37 2 B B - 42
Multi-function Output Functions
Setting
Control Methods
Setting
value Function Open loop
Vector
Flux vector
Page
0 During run ON: run command is ON or voltage is being output) - 43
1 Zero-speed - 43
2 Frequency agree 1: (Detection width L4-02) - 54
3 Desired frequency agree 1 (ON: Output frequency = rL4-01, detection width in L4-02) - 54
4
Frequency (Four) detection 1 (ON: +L4-01 output frequency--L4-01, detection width in
L4-02)
- 54
5
Frequency (Four) detection 2
(ON: Output frequency
+L4-01 or output frequency%--L4-01, detection width in L4-02)
- 54
6 Inverter operation ready READY: After initialization, no faults
7 During DC bus undervoltage (UV) detection
8 During baseblock (ON: during baseblock)
9 Frequency reference selection (ON: Frequency reference from Operator)
A Run command selection (ON: Run command from Operator)
B Overtorque detection 1 NO (NO contact: Overtorque detection at ON) - 56
C
Loss of frequency reference (Effective when operation selection is “1” for L4-05 frequency
reference missing)
- 54
D Braking resistor fault (ON: Resistor overheat or braking transistor fault)
E Fault (ON: Faults other than CPF00, CPF01 have occurred.) NO TAG
F Not used. (Do not set.)
10 Minor fault (ON: Alarm displayed) NO TAG
11 Fault reset command active
12 Not used. (Do not set.)
13 Frequency agree 2 (Detection width: L4-04) - 54
14 Desired frequency agree 2 (ON: Output frequency = L4-03, detection width in L4-04) - 54
15 Frequency detection 3 (ON: Output frequency %--L4-03, detection width in L4-04) - 54
16 Frequency detection 4 (ON: Output frequency --L4-03, detection width in L4-04) - 54
17 Overtorque detection 1 NC (NC Contact: Ttorque detection at OFF) - 56
18 Overtorque detection 2 NO (NO Contact: Torque detection at ON) - 56
19 Overtorque detection 2 NC (NC Contact: Torque detection at OFF) - 56
1A During reverse run (ON: During reverse run)
1B During baseblock 2 (OFF: During baseblock)
1C Motor selection (ON:During moter 1 selection)
1D Regenerating (ON: Regenerating)
1E Restart enabled (ON: Restart enabled) - 56
1F Motor overload (OL1) pre-alarm (ON: 90% or more of the detection level) - 43
20 Inverter overheat (OH) pre-alarm (ON: Temperature exceeds L8-02 setting) - 43
30 During torque limit (current limit) (ON: During torque limit)
31 During speed limit. (ON: During speed limit) - 43
37
During run 2 (ON: Frequency output, OFF: Base block, DC injection braking, initial excita-
tion, operation stop.)
- 43
8